A protected pack only trickle-charges, so Dream, the 12V rail, and the amp stay off until the pack is above 6.8V. Firmware is 0.2.51.
Co-authored-by: Cursor <cursoragent@cursor.com>
Dream power-up now overlaps the boot light show. Mode keys, the pick, and side keys stay ignored until MIDI config has been sent, so a fast tap cannot play before the board is ready.
Co-authored-by: Cursor <cursoragent@cursor.com>
Boot and song changes use the universal and rhythm BPM tables, with style 20 at 91. Factory restore and power-on now follow the persistence sheet, and the firmware version is 0.2.49.
Co-authored-by: Cursor <cursoragent@cursor.com>
Bump firmware to 0.2.44 so slot 1 stays Bank1 program 24 and slot 2 stays program 25. Rhythm presets no longer replace the string voice on channel 0.
Co-authored-by: Cursor <cursoragent@cursor.com>
Hold master mute from shortly after the boost turns on through EQ setup, then let the chip fade in so boot does not pop.
Co-authored-by: Cursor <cursoragent@cursor.com>
Bring up 12V and Dream together after the boot lights, then configure the amp a single time so the string tone stays intact and the unmute write is not lost.
Co-authored-by: Cursor <cursoragent@cursor.com>
Show the real battery percent, shut down at 6.8V even while Type-C is connected, and leave the charge screen dark so it does not drain the pack. Initialize the amplifier only after the 12V rail has settled.
Co-authored-by: Cursor <cursoragent@cursor.com>
Bump firmware to 0.2.31. Skip the color LED sequence on USB power-on so a depleted pack can leave the logo screen and charge normally.
Co-authored-by: Cursor <cursoragent@cursor.com>
Bump firmware to 0.2.30. The 11px font now has the update glyphs, and the flashed boot image stays in USB programming when that mode is saved.
Co-authored-by: Cursor <cursoragent@cursor.com>
Match the card box to the reference, put the value on the same center line as the arrow and plus-minus chips, and use MiSans for the 16px digits.
Co-authored-by: Cursor <cursoragent@cursor.com>
Centralize idle-timer reset on touch/volume/tap/transpose in UI task, and on pick, fretboard, side keys, round keys, and string NoteOn. Pause auto power-off countdown while accompaniment is playing.
Co-authored-by: Cursor <cursoragent@cursor.com>
Restore hard AutoBandTop1_Stop and drop eaten-start/followup tick-gate.
Keep API stubs for callers. Block TM1617 round keys and reinforce side-key/BLE gates while InModeFlag is false.
Co-authored-by: Cursor <cursoragent@cursor.com>
NavBar no longer forces I after stop; remember context before leave and prefer saved fret chord on no-fret pick.
Co-authored-by: Cursor <cursoragent@cursor.com>
Normal-mode pick with no fret held applies the last expert stop transpose, starts on I, and arms even-beat stop if idle.
Co-authored-by: Cursor <cursoragent@cursor.com>
Init TM1629 before POWER_ON and run the color sequence during the logo dwell instead of after mode select.
Co-authored-by: Cursor <cursoragent@cursor.com>
Normal and expert modes no longer wait for the next bar before preamble, interlude, outro, and ending. Universal mode ignores those keys. Bump firmware to 0.2.22.
Co-authored-by: Cursor <cursoragent@cursor.com>
Universal TM1629 path dropped keys 0-21 before BP_Transpose. Route pick-hold neck keys to transpose, add RTT pick hold inject and a HIL script.
Co-authored-by: Cursor <cursoragent@cursor.com>
TM1617 keys injected fake touches at y=255 which slammed mixer sliders to 1. Lock the pressed fader until release and shrink overlapping hit boxes.
Co-authored-by: Cursor <cursoragent@cursor.com>
Loop_Light_Handle was hardcoding red for every measure; map L1-L7 to the same R/G/B/yellow/purple/cyan/white table as App guide LEDs.
Co-authored-by: Cursor <cursoragent@cursor.com>
Problem2: in song mode UI shows 6m(Am) but MIDI played AM7
(E2 A2 E3 G#3 C#4 E4). Root cause: BL_Set_led wrote the LED frame's
chord code into chord_type_index_map of the group middle key
(LED_L6 -> key17), so a guidance frame carrying 0x02 (M7) turned the
Am key into AM7. Remapping on the chord page only helped until the
next LED frame.
- BL_Set_led: light LED only, drop all chord_type_index_map writes;
chord quality is owned by map page 02 03/02 04 (BT_Chord_offset_map)
- handleReadRhythmMap / Return_Light_buff: fix type->protocol read-back
encoding (m7->0x0A, M7->0x02, ad9->0x04, m7-5->0x0B, sus2->0x1F,
sus4->0x1E), re-landing the 0917 verified fix
- BT_Chord_offset_map: accept dominant-7 doc code 0x0D (legacy 0x13 kept)
- tests: test_chord_map_fix.py (16/16 PASS on device),
test_fret_positions.py, test_problem2_song_am.py (7/7 PASS:
post-LED strum stays E2 A2 E3 A3 C4 E4)
Co-authored-by: Cursor <cursoragent@cursor.com>
Low-battery shutdown below 6.2V with tip screen and 10s soft power-off; UI0902 includes LOWBAT_TIP fullscreen asset.
Co-authored-by: Cursor <cursoragent@cursor.com>
Stop all sound, show UI0902 LOWBAT_TIP fullscreen, then soft-off after 10s. Skip while charging; speed up ADC sampling near empty. Pack new tip bitmap into ExtFlash UI0902 map.
Co-authored-by: Cursor <cursoragent@cursor.com>
Disable LOOP_LIGHT rhythm chasing in free mode so LEDs stay solid green instead of moving with the beat.
Co-authored-by: Cursor <cursoragent@cursor.com>
Free-mode even-beat release stop; keep fret KEY_ID during wind-down so register octave does not jump up before stop. Also includes universal outro all-green LED and expert local-song continue after section+fret.
Co-authored-by: Cursor <cursoragent@cursor.com>
yuquanjun