Keep the NVM sector out of the application image and arm a backup register that survives reset, so confirm stays in flash mode even when round key 4 is not held.
Co-authored-by: Cursor <cursoragent@cursor.com>
Match the requirement screen using the settings-hub method, and keep the glyphs 1-bit so the image still fits in application flash.
Co-authored-by: Cursor <cursoragent@cursor.com>
Show the real battery percent, shut down at 6.8V even while Type-C is connected, and leave the charge screen dark so it does not drain the pack. Initialize the amplifier only after the 12V rail has settled.
Co-authored-by: Cursor <cursoragent@cursor.com>
Bump firmware to 0.2.30. The 11px font now has the update glyphs, and the flashed boot image stays in USB programming when that mode is saved.
Co-authored-by: Cursor <cursoragent@cursor.com>
Remove divider lines, add language and USB-update confirm pages, and store both in NVM so boot can enter IAP.
Co-authored-by: Cursor <cursoragent@cursor.com>
Stop all sound, show UI0902 LOWBAT_TIP fullscreen, then soft-off after 10s. Skip while charging; speed up ADC sampling near empty. Pack new tip bitmap into ExtFlash UI0902 map.
Co-authored-by: Cursor <cursoragent@cursor.com>
TMR7 high-prio watchdog and fault-loop emergency cut/reset so soft-off still works if the main loop or AutoBand ISR dies; skip start when preset load fails.
Co-authored-by: Cursor <cursoragent@cursor.com>
Update pack/publish to enforce 41KB song limit, verify 1/2/3.bin at fixed addresses, and emit .res aliases for the tone and ALL extflash images.
Co-authored-by: Cursor <cursoragent@cursor.com>
Point system-settings rows at the correct Flash icons, keep Main/UI alive across soft-off, and expose git build id for 01 0C with matching BLE tests.
Co-authored-by: Cursor <cursoragent@cursor.com>
TaskBTRecvThread previously started only after mode select, so GATT SysEx never reached the parser until then; verified BLE-MIDI 01 01 now replies with GATT notify.
Co-authored-by: Cursor <cursoragent@cursor.com>
Replace settings-hub mixer/gear bitmaps, and show Boot IAP screen from UI0902_FLASH_MODE in external Flash.
Co-authored-by: Cursor <cursoragent@cursor.com>
Charge page draws UI0902_CHARGE_SCREEN instead of legacy 160x190 Charg.bin; pack/gen/publish paths keep the asset in sync.
Co-authored-by: Cursor <cursoragent@cursor.com>
UI shows LocalSongNames instead of bare indices; pack regenerates the header; WQY font gains the four display characters.
Co-authored-by: Cursor <cursoragent@cursor.com>
Fill three mode rows to the screen bottom without a nav bar, and fix the status bar to one volume meter, centered Bluetooth, and battery percentage.
Co-authored-by: Cursor <cursoragent@cursor.com>
- Mode select page draws 222x84 row bitmaps from external flash
- Mixer page uses flash track/knob images with picture labels
- Settings and restore pages re-laid out with 0902 row style
- New status bar icons and battery outline+clip fill rendering
- Add LCD_WR_PIC_ClipX and LCD_WR_PIC_FROM_FLASH_Trans draw APIs
- Replace 4-tab bar with GUI_NAV_BAR 3-icon bottom navigation
- Swap 0831 assets for UI0902 in the IAR project file
Co-authored-by: Cursor <cursoragent@cursor.com>
Harden reset/recover when RTT is missing, and stream touch/UI events only on press for field debugging.
Co-authored-by: Cursor <cursoragent@cursor.com>
Replace on-device Chinese glyphs with MiSans icon+text row assets so the trial format matches the designer's export.
Co-authored-by: Cursor <cursoragent@cursor.com>
Keep AT32F403ARCT7 RAM at 96KB, soft-CS GRAM readback over RTT, and add missing 普/通/业 to CHS16 so mode labels render fully.
Co-authored-by: Cursor <cursoragent@cursor.com>
Switch OGCoreOrChip to core mode and set J-Link flash device to Cortex-M4 to avoid CMSIS Unknown target when the chip is not selected in the IDE.
Co-authored-by: Cursor <cursoragent@cursor.com>
yuquanjun