Disable the cascade IRQ in the cascade handler. This is required to
get the DB1300 working, and also gets rid of all spurious interrupts
previously observed on the DB1200; so Config[OD] can be disabled
again for better performance.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2708/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Setting Config[OD] gets rid of a _LOT_ of spurious CPLD interrupts,
but also decreases overall performance a bit.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2347/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Same issues as SD card detection: One of both is always triggering and the
handlers take care to shut it up and enable the other. To avoid messages
about "unbalanced interrupt enable/disable" they must not be automatically
enabled when initally requested.
This was not an issue with the db1200_defconfig due to fortunate timings;
on a build without network chip support the warnings appear.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1133/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
While playing with the out-of-tree MAE driver module, the system would
panic after a while in the db1200 custom wait code after wakeup due to
a clobbered k0 register being used as target address of a store op.
Remove the custom wait implementation and revert back to the Alchemy-
recommended implementation already set as default.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1092/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Implement reset / poweroff in the board code instead. The peripheral reset
code is gone too since YAMON which all in-tree boards use does the same
work when it boots.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/783/
Patchwork: http://patchwork.linux-mips.org/patch/882/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Create own directory for DB1200 code and update it with new features.
- SPI support:
- tmp121 temperature sensor
- SPI flash on DB1200
- I2C support
- NE1619 sensor
- AT24 eeprom
- I2C/SPI can be selected at boot time via switch S6.8
- Carddetect IRQs for SD cards.
- gen_nand based NAND support.
- hexleds count sleep/wake transitions.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Manuel Lauss