[ Upstream commit 7e842d70fe599bc13594b650b2144c4b6e6d6bf1 ]
HyperFlash devices fail to probe:
rpc-if-hyperflash rpc-if-hyperflash: probing of hyperbus device failed
In HyperFlash or Octal-SPI Flash mode, the Transfer Data Enable bits
(SPIDE) in the Manual Mode Enable Setting Register (SMENR) are derived
from half of the transfer size, cfr. the rpcif_bits_set() helper
function. However, rpcif_reg_{read,write}() does not take the bus size
into account, and does not double all Manual Mode Data Register access
sizes when communicating with a HyperFlash or Octal-SPI Flash device.
Fix this, and avoid the back-and-forth conversion between transfer size
and Transfer Data Enable bits, by explicitly storing the transfer size
in struct rpcif, and using that value to determine access size in
rpcif_reg_{read,write}().
Enforce that the "high" Manual Mode Read/Write Data Registers
(SM[RW]DR1) are only used for 8-byte data accesses.
While at it, forbid writing to the Manual Mode Read Data Registers,
as they are read-only.
Fixes: fff53a551db50f5e ("memory: renesas-rpc-if: Correct QSPI data transfer in Manual mode")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/cde9bfacf704c81865f57b15d1b48a4793da4286.1649681476.git.geert+renesas@glider.be
Link: https://lore.kernel.org/r/20220420070526.9367-1-krzysztof.kozlowski@linaro.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b452dbf24d7d9a990d70118462925f6ee287d135 upstream.
Make sure to free the flash platform device in the event that
registration fails during probe.
Fixes: ca7d8b980b ("memory: add Renesas RPC-IF driver")
Cc: stable@vger.kernel.org # 5.8
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20220303180632.3194-1-johan@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fff53a551db50f5edecaa0b29a64056ab8d2bbca upstream.
This patch fixes 2 problems:
[1] The output warning logs and data loss when performing
mount/umount then remount the device with jffs2 format.
[2] The access width of SMWDR[0:1]/SMRDR[0:1] register is wrong.
This is the sample warning logs when performing mount/umount then
remount the device with jffs2 format:
jffs2: jffs2_scan_inode_node(): CRC failed on node at 0x031c51d4:
Read 0x00034e00, calculated 0xadb272a7
The reason for issue [1] is that the writing data seems to
get messed up.
Data is only completed when the number of bytes is divisible by 4.
If you only have 3 bytes of data left to write, 1 garbage byte
is inserted after the end of the write stream.
If you only have 2 bytes of data left to write, 2 bytes of '00'
are added into the write stream.
If you only have 1 byte of data left to write, 2 bytes of '00'
are added into the write stream. 1 garbage byte is inserted after
the end of the write stream.
To solve problem [1], data must be written continuously in serial
and the write stream ends when data is out.
Following HW manual 62.2.15, access to SMWDR0 register should be
in the same size as the transfer size specified in the SPIDE[3:0]
bits in the manual mode enable setting register (SMENR).
Be sure to access from address 0.
So, in 16-bit transfer (SPIDE[3:0]=b'1100), SMWDR0 should be
accessed by 16-bit width.
Similar to SMWDR1, SMDDR0/1 registers.
In current code, SMWDR0 register is accessed by regmap_write()
that only set up to do 32-bit width.
To solve problem [2], data must be written 16-bit or 8-bit when
transferring 1-byte or 2-byte.
Fixes: ca7d8b980b ("memory: add Renesas RPC-IF driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Duc Nguyen <duc.nguyen.ub@renesas.com>
[wsa: refactored to use regmap only via reg_read/reg_write]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210922091007.5516-1-wsa+renesas@sang-engineering.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 59e27d7c94aa02da039b000d33c304c179395801 ]
The platform_get_resource_byname() can return NULL which would be
immediately dereferenced by resource_size(). Instead dereference it
after validating the resource.
Addresses-Coverity: Dereference null return value
Fixes: ca7d8b980b ("memory: add Renesas RPC-IF driver")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210407154357.70200-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a0453f4ed066cae651b3119ed11f52d31dae1eca upstream.
In the error path of rpcif_manual_xfer() the value of ret is overwritten
by value returned by reset_control_reset() function and thus returning
incorrect value to the caller.
This patch makes sure the correct value is returned to the caller of
rpcif_manual_xfer() by dropping the overwrite of ret in error path.
Also now we ignore the value returned by reset_control_reset() in the
error path and instead print a error message when it fails.
Fixes: ca7d8b980b ("memory: add Renesas RPC-IF driver")
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Pavel Machek (CIP) <pavel@denx.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201126191146.8753-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the memory driver for Renesas RPC-IF which registers either SPI or
HyperFLash device depending on the contents of the device tree subnode.
It also provides the absract "back end" device APIs that can be used by
the "front end" SPI/MTD drivers to talk to the real hardware.
Based on the original patch by Mason Yang <masonccyang@mxic.com.tw>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Link: https://lore.kernel.org/r/9a3606ec-d4d0-c63a-4fb6-631ab38e621c@cogentembedded.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Geert Uytterhoeven