commit 637674fa40059cddcc3ad2212728965072f62ea3 upstream.
The EndRun PTP/1588 dual serial port device is based on the Oxford
Semiconductor OXPCIe952 UART device with the PCI vendor:device ID set
for EndRun Technologies and is therefore driven by a fixed 62.5MHz clock
input derived from the 100MHz PCI Express clock. The clock rate is
divided by the oversampling rate of 16 as it is supplied to the baud
rate generator, yielding the baud base of 3906250.
Replace the incorrect baud base of 4000000 with the right value of
3906250 then, complementing commit 6cbe45d8ac93 ("serial: 8250: Correct
the clock for OxSemi PCIe devices").
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Cc: stable <stable@kernel.org>
Fixes: 1bc8cde46a ("8250_pci: Added driver for Endrun Technologies PTP PCIe card.")
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204181515270.9383@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e6eebdf5e2455f089ccd000754a0deaeb79af82 upstream.
Sticky MCR bits are lost in console restoration if console suspending
has been disabled. This currently affects the AFE bit, which works in
combination with RTS which we set, so we want to make sure the UART
retains control of its FIFO where previously requested. Also specific
drivers may need other bits in the future.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: 4516d50aab ("serial: 8250: Use canary to restart console after suspend")
Cc: stable@vger.kernel.org # v4.0+
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204181518490.9383@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f58c252e30cf74f68b0054293adc03b5923b9f0e ]
When 8250 UART is using DMA, x_char (XON/XOFF) is never sent
to the wire. After this change, x_char is injected correctly.
Create uart_xchar_out() helper for sending the x_char out and
accounting related to it. It seems that almost every driver
does these same steps with x_char. Except for 8250, however,
almost all currently lack .serial_out so they cannot immediately
take advantage of this new helper.
The downside of this patch is that it might reintroduce
the problems some devices faced with mixed DMA/non-DMA transfer
which caused revert f967fc8f16 (Revert "serial: 8250_dma:
don't bother DMA with small transfers"). However, the impact
should be limited to cases with XON/XOFF (that didn't work
with DMA capable devices to begin with so this problem is not
very likely to cause a major issue, if any at all).
Fixes: 9ee4b83e51 ("serial: 8250: Add support for dmaengine")
Reported-by: Gilles Buloz <gilles.buloz@kontron.com>
Tested-by: Gilles Buloz <gilles.buloz@kontron.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220314091432.4288-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dedab69fd650ea74710b2e626e63fd35584ef773 ]
Set em485->active_timer = NULL isn't always enough to take out the stop
timer. While there is a check that it acts in the right state (i.e.
waiting for RTS-after-send to pass after sending some chars) but the
following might happen:
- CPU1: some chars send, shifter becomes empty, stop tx timer armed
- CPU0: more chars send before RTS-after-send expired
- CPU0: shifter empty irq, port lock taken
- CPU1: tx timer triggers, waits for port lock
- CPU0: em485->active_timer = &em485->stop_tx_timer, hrtimer_start(),
releases lock()
- CPU1: get lock, see em485->active_timer == &em485->stop_tx_timer,
tear down RTS too early
This fix bases on research done by Steffen Trumtrar.
Fixes: b86f86e8e7 ("serial: 8250: fix potential deadlock in rs485-mode")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220215160236.344236-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5318f70da7e82649d794fc27d8a127c22aa3566e ]
The pci_get_slot() increases its reference count, the caller
must decrement the reference count by calling pci_dev_put().
Fixes: 9a1870ce81 ("serial: 8250: don't use slave_id of dma_slave_config")
Depends-on: a13e19cf3d ("serial: 8250_lpss: split LPSS driver to separate module")
Reported-by: Qing Wang <wangqing@vivo.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220223151240.70248-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6e8793674bb0d1135ca0e5c9f7e16fecbf815926 upstream.
There is a build error when using a kernel .config file from
'kernel test robot' for a different build problem:
hppa64-linux-ld: drivers/tty/serial/8250/8250_gsc.o: in function `.LC3':
(.data.rel.ro+0x18): undefined reference to `iosapic_serial_irq'
when:
CONFIG_GSC=y
CONFIG_SERIO_GSCPS2=y
CONFIG_SERIAL_8250_GSC=y
CONFIG_PCI is not set
and hence PCI_LBA is not set.
IOSAPIC depends on PCI_LBA, so IOSAPIC is not set/enabled.
Make the use of iosapic_serial_irq() conditional to fix the build error.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: linux-parisc@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-serial@vger.kernel.org
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Johan Hovold <johan@kernel.org>
Suggested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 152d1afa834c84530828ee031cf07a00e0fc0b8c upstream.
This commit adds support for the some of the Brainboxes PCI range of
cards, including the UC-101, UC-235/246, UC-257, UC-268, UC-275/279,
UC-302, UC-310, UC-313, UC-320/324, UC-346, UC-357, UC-368
and UC-420/431.
Signed-off-by: Cameron Williams <cang1@live.co.uk>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/AM5PR0202MB2564688493F7DD9B9C610827C45E9@AM5PR0202MB2564.eurprd02.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d06b1cf28297e27127d3da54753a3a01a2fa2f28 upstream.
8250_of supports a reg-offset property which is intended to handle
cases where the device registers start at an offset inside the region
of memory allocated to the device. The Xilinx 16550 UART, for which this
support was initially added, requires this. However, the code did not
adjust the overall size of the mapped region accordingly, causing the
driver to request an area of memory past the end of the device's
allocation. For example, if the UART was allocated an address of
0xb0130000, size of 0x10000 and reg-offset of 0x1000 in the device
tree, the region of memory reserved was b0131000-b0140fff, which caused
the driver for the region starting at b0140000 to fail to probe.
Fix this by subtracting reg-offset from the mapped region size.
Fixes: b912b5e2cf ([POWERPC] Xilinx: of_serial support for Xilinx uart 16550.)
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220112194214.881844-1-robert.hancock@calian.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c33ff728812aa18792afffaf2c9873b898e7512 upstream.
Commit fab8a02b73 ("serial: 8250_fintek: Enable high speed mode on Fintek F81866")
introduced support to use high baudrate with Fintek SuperIO UARTs. It'll
change clocksources when the UART probed.
But when user add kernel parameter "console=ttyS0,115200 console=tty0" to make
the UART as console output, the console will output garbled text after the
following kernel message.
[ 3.681188] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
The issue is occurs in following step:
probe_setup_port() -> fintek_8250_goto_highspeed()
It change clocksource from 115200 to 921600 with wrong time, it should change
clocksource in set_termios() not in probed. The following 3 patches are
implemented change clocksource in fintek_8250_set_termios().
Commit 58178914ae ("serial: 8250_fintek: UART dynamic clocksource on Fintek F81216H")
Commit 195638b6d4 ("serial: 8250_fintek: UART dynamic clocksource on Fintek F81866")
Commit 423d9118c6 ("serial: 8250_fintek: Add F81966 Support")
Due to the high baud rate had implemented above 3 patches and the patch
Commit fab8a02b73 ("serial: 8250_fintek: Enable high speed mode on Fintek F81866")
is bugged, So this patch will remove it.
Fixes: fab8a02b73 ("serial: 8250_fintek: Enable high speed mode on Fintek F81866")
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Link: https://lore.kernel.org/r/20211215075835.2072-1-hpeter+linux_kernel@gmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f85e04503f369b3f2be28c83fc48b74e19936ebc upstream.
Commit f45709df77 ("serial: 8250: Don't touch RTS modem control while
in rs485 mode") sought to prevent user space from interfering with rs485
communication by ignoring a TIOCMSET ioctl() which changes RTS polarity.
It did so in serial8250_do_set_mctrl(), which turns out to be too deep
in the call stack: When a uart_port is opened, RTS polarity is set by
the rs485-aware function uart_port_dtr_rts(). It calls down to
serial8250_do_set_mctrl() and that particular RTS polarity change should
*not* be ignored.
The user-visible result is that on 8250_omap ports which use rs485 with
inverse polarity (RTS bit in MCR register is 1 to receive, 0 to send),
a newly opened port initially sets up RTS for sending instead of
receiving. That's because omap_8250_startup() sets the cached value
up->mcr to 0 and omap_8250_restore_regs() subsequently writes it to the
MCR register. Due to the commit, serial8250_do_set_mctrl() preserves
that incorrect register value:
do_sys_openat2
do_filp_open
path_openat
vfs_open
do_dentry_open
chrdev_open
tty_open
uart_open
tty_port_open
uart_port_activate
uart_startup
uart_port_startup
serial8250_startup
omap_8250_startup # up->mcr = 0
uart_change_speed
serial8250_set_termios
omap_8250_set_termios
omap_8250_restore_regs
serial8250_out_MCR # up->mcr written
tty_port_block_til_ready
uart_dtr_rts
uart_port_dtr_rts
serial8250_set_mctrl
omap8250_set_mctrl
serial8250_do_set_mctrl # mcr[1] = 1 ignored
Fix by intercepting RTS changes from user space in uart_tiocmset()
instead.
Link: https://lore.kernel.org/linux-serial/20211027111644.1996921-1-baocheng.su@siemens.com/
Fixes: f45709df77 ("serial: 8250: Don't touch RTS modem control while in rs485 mode")
Cc: Chao Zeng <chao.zeng@siemens.com>
Cc: stable@vger.kernel.org # v5.7+
Reported-by: Su Bao Cheng <baocheng.su@siemens.com>
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Tested-by: Su Bao Cheng <baocheng.su@siemens.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/21170e622a1aaf842a50b32146008b5374b3dd1d.1637596432.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb1201d4b38ec67bd9a871cf86b0cc10f28b15b5 upstream.
Have pericom_do_set_divisor() use the uartclk instead of a hard coded
value to work with different speed crystals. Tested with 14.7456 and 24
MHz crystals.
Have pericom_do_set_divisor() always calculate the divisor rather than
call serial8250_do_set_divisor() for rates below baud_base.
Do not write registers or call serial8250_do_set_divisor() if valid
divisors could not be found.
Fixes: 6bf4e42f1d ("serial: 8250: Add support for higher baud rates to Pericom chips")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jay Dolan <jay.dolan@accesio.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211122120604.3909-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c525c5d2437f93520388920baac6d9340c65d239 upstream.
Fix error in table for PCI_DEVICE_ID_ACCESIO_PCIE_ICM_4S that caused it
and PCI_DEVICE_ID_ACCESIO_PCIE_ICM232_4 to be missing their fourth port.
Fixes: 78d3820b9b ("serial: 8250_pci: Have ACCES cards that use the four port Pericom PI7C9X7954 chip use the pci_pericom_setup()")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jay Dolan <jay.dolan@accesio.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211122120604.3909-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ebabb77a2a115b6c5e68f7364b598310b5f61fb2 ]
ACPI_PTR() is more harmful than helpful. For example, in this case
if CONFIG_ACPI=n, the ID table left unused which is not what we want.
Instead of adding ifdeffery here and there, drop ACPI_PTR().
Fixes: 6a7320c466 ("serial: 8250_dw: Add ACPI 5.0 support")
Reported-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211005134516.23218-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 211cde4f5817dc88ef7f8f2fa286e57fbf14c8ee upstream.
Commit 868f3ee6e4 ("serial: 8250: Add 8250 port clock update method")
added a hack to support SoCs where the UART reference clock can
change behind the back of the driver but failed to add the proper
locking.
First, make sure to take a reference to the tty struct to avoid
dereferencing a NULL pointer if the clock change races with a hangup.
Second, the termios semaphore must be held during the update to prevent
a racing termios change.
Fixes: 868f3ee6e4 ("serial: 8250: Add 8250 port clock update method")
Fixes: c8dff3aa82 ("serial: 8250: Skip uninitialized TTY port baud rate update")
Cc: stable@vger.kernel.org # 5.9
Cc: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211015111422.1027-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 79e9e30a9292a62d25ab75488d3886108db1eaad upstream.
Commit b67e830d38fa ("serial: 8250: 8250_omap: Fix possible interrupt
storm on K3 SoCs") introduced fixup including a register read to
RX_LVL, however, we should be using word offset than byte offset
since our registers are on 4 byte boundary (port.regshift = 2) for
8250_omap.
Fixes: b67e830d38fa ("serial: 8250: 8250_omap: Fix possible interrupt storm on K3 SoCs")
Cc: stable <stable@vger.kernel.org>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210903050550.29050-1-nm@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1fe0e1fa3209ad8e9124147775bd27b1d9f04bd4 ]
Handle optional overrun-throttle-ms property as done for 8250_fsl in commit
6d7f677a2a ("serial: 8250: Rate limit serial port rx interrupts during
input overruns"). This can be used to rate limit the UART interrupts on
noisy lines that end up producing messages like the following:
ttyS ttyS2: 4 input overrun(s)
At least on droid4, the multiplexed USB and UART port is left to UART mode
by the bootloader for a debug console, and if a USB charger is connected
on boot, we get noise on the UART until the PMIC related drivers for PHY
and charger are loaded.
With this patch and overrun-throttle-ms = <500> we avoid the extra rx
interrupts.
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210727103533.51547-2-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a96e97ab4e835078e6f27b7e1c0947814df3841 ]
The bar and offset parameters to setup_port() are used in pointer math,
and while it would be very difficult to get them to wrap as a negative
number, just be "safe" and make them unsigned so that static checkers do
not trip over them unintentionally.
Cc: Jiri Slaby <jirislaby@kernel.org>
Reported-by: Jordy Zomer <jordy@pwning.systems>
Link: https://lore.kernel.org/r/20210726130717.2052096-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7aff291d069c4418285f3c8ee27b0ff67ce5998 ]
Oxford Semiconductor 950 serial port devices have a 128-byte FIFO and in
the enhanced (650) mode, which we select in `autoconfig_has_efr' with
the ECB bit set in the EFR register, they support the receive interrupt
trigger level selectable with FCR bits 7:6 from the set of 16, 32, 112,
120. This applies to the original OX16C950 discrete UART[1] as well as
950 cores embedded into more complex devices.
For these devices we set the default to 112, which sets an excessively
high level of 112 or 7/8 of the FIFO capacity, unlike with other port
types where we choose at most 1/2 of their respective FIFO capacities.
Additionally we don't make the trigger level configurable. Consequently
frequent input overruns happen with high bit rates where hardware flow
control cannot be used (e.g. terminal applications) even with otherwise
highly-performant systems.
Lower the default receive interrupt trigger level to 32 then, and make
it configurable. Document the trigger levels along with other port
types, including the set of 16, 32, 64, 112 for the transmit interrupt
as well[2].
References:
[1] "OX16C950 rev B High Performance UART with 128 byte FIFOs", Oxford
Semiconductor, Inc., DS-0031, Sep 05, Table 10: "Receiver Trigger
Levels", p. 22
[2] same, Table 9: "Transmit Interrupt Trigger Levels", p. 22
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260608480.37803@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6f991850412963381017cfb0d691cbd4d6a551dc upstream.
With commit 439c7183e5b9 ("serial: 8250: 8250_omap: Disable RX interrupt after DMA enable"),
below warning is seen with W=1 and CONFIG_SERIAL_8250_DMA is disabled:
drivers/tty/serial/8250/8250_omap.c:1199:42: warning: unused variable 'k3_soc_devices' [-Wunused-const-variable]
Fix this by moving the code using k3_soc_devices array to
omap_serial_fill_features_erratas() that handles other errata flags as
well.
Fixes: 439c7183e5b9 ("serial: 8250: 8250_omap: Disable RX interrupt after DMA enable")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20201111112653.2710-2-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d4548b14dd7e5c698f81ce23ce7b69a896373b45 upstream.
k3_soc_devices array is missing a sentinel entry which may result in out
of bounds access as reported by kernel KASAN.
Fix this by adding a sentinel entry.
Fixes: 439c7183e5b9 ("serial: 8250: 8250_omap: Disable RX interrupt after DMA enable")
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20201111112653.2710-1-vigneshr@ti.com
Signed-off-by: Nobuhiro Iwamatsu (CIP) <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 341abd693d10e5f337a51f140ae3e7a1ae0febf6 upstream.
This attempts to fix a bug found with a serial port card which uses
an MCS9922 chip, one of the 4 models for which MSI-X interrupts are
currently supported. I don't possess such a card, and i'm not
experienced with the serial subsystem, so this patch is based on what
i think i found as a likely reason for failure, based on walking the
user who actually owns the card through some diagnostic.
The user who reported the problem finds the following in his dmesg
output for the relevant ttyS4 and ttyS5:
[ 0.580425] serial 0000:02:00.0: enabling device (0000 -> 0003)
[ 0.601448] 0000:02:00.0: ttyS4 at I/O 0x3010 (irq = 125, base_baud = 115200) is a ST16650V2
[ 0.603089] serial 0000:02:00.1: enabling device (0000 -> 0003)
[ 0.624119] 0000:02:00.1: ttyS5 at I/O 0x3000 (irq = 126, base_baud = 115200) is a ST16650V2
...
[ 6.323784] genirq: Flags mismatch irq 128. 00000080 (ttyS5) vs. 00000000 (xhci_hcd)
[ 6.324128] genirq: Flags mismatch irq 128. 00000080 (ttyS5) vs. 00000000 (xhci_hcd)
...
Output of setserial -a:
/dev/ttyS4, Line 4, UART: 16650V2, Port: 0x3010, IRQ: 127
Baud_base: 115200, close_delay: 50, divisor: 0
closing_wait: 3000
Flags: spd_normal skip_test
This suggests to me that the serial driver wants to register and share a
MSI/MSI-X irq 128 with the xhci_hcd driver, whereas the xhci driver does
not want to share the irq, as flags 0x00000080 (== IRQF_SHARED) from the
serial port driver means to share the irq, and this mismatch ends in some
failed irq init?
With this setup, data reception works very unreliable, with dropped data,
already at a transmission rate of only a 16 Bytes chunk every 1/120th of
a second, ie. 1920 Bytes/sec, presumably due to rx fifo overflow due to
mishandled or not used at all rx irq's?
See full discussion thread with attempted diagnosis at:
https://psychtoolbox.discourse.group/t/issues-with-iscan-serial-port-recording/3886
Disabling the use of MSI interrupts for the serial port pci card did
fix the reliability problems. The user executed the following sequence
of commands to achieve this:
echo 0000:02:00.0 | sudo tee /sys/bus/pci/drivers/serial/unbind
echo 0000:02:00.1 | sudo tee /sys/bus/pci/drivers/serial/unbind
echo 0 | sudo tee /sys/bus/pci/devices/0000:02:00.0/msi_bus
echo 0 | sudo tee /sys/bus/pci/devices/0000:02:00.1/msi_bus
echo 0000:02:00.0 | sudo tee /sys/bus/pci/drivers/serial/bind
echo 0000:02:00.1 | sudo tee /sys/bus/pci/drivers/serial/bind
This resulted in the following log output:
[ 82.179021] pci 0000:02:00.0: MSI/MSI-X disallowed for future drivers
[ 87.003031] pci 0000:02:00.1: MSI/MSI-X disallowed for future drivers
[ 98.537010] 0000:02:00.0: ttyS4 at I/O 0x3010 (irq = 17, base_baud = 115200) is a ST16650V2
[ 103.648124] 0000:02:00.1: ttyS5 at I/O 0x3000 (irq = 18, base_baud = 115200) is a ST16650V2
This patch attempts to fix the problem by disabling irq sharing when
using MSI irq's. Note that all i know for sure is that disabling MSI
irq's fixed the problem for the user, so this patch could be wrong and
is untested. Please review with caution, keeping this in mind.
Fixes: 8428413b1d ("serial: 8250_pci: Implement MSI(-X) support")
Cc: Ralf Ramsauer <ralf.ramsauer@oth-regensburg.de>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Link: https://lore.kernel.org/r/20210729043306.18528-1-mario.kleiner.de@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f0909db761535aefafa77031062603a71557267 upstream.
Elkhart Lake UARTs are PCI enumerated Synopsys DesignWare v4.0+ UART
integrated with Intel iDMA 32-bit DMA controller. There is a specific
driver to handle them, i.e. 8250_lpss. Hence, disable 8250_pci
enumeration for these UARTs.
Fixes: 1b91d97c66 ("serial: 8250_lpss: Add ->setup() for Elkhart Lake ports")
Fixes: 4f912b898d ("serial: 8250_lpss: Enable HS UART on Elkhart Lake")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210713101739.36962-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5227c51090e165db4b48dcaa300605bfced7014 upstream.
Make sure only actual 8 bits of the IIR register are used in determining
the port type in `autoconfig'.
The `serial_in' port accessor returns the `unsigned int' type, meaning
that with UPIO_AU, UPIO_MEM16, UPIO_MEM32, and UPIO_MEM32BE access types
more than 8 bits of data are returned, of which the high order bits will
often come from bus lines that are left floating in the data phase. For
example with the MIPS Malta board's CBUS UART, where the registers are
aligned on 8-byte boundaries and which uses 32-bit accesses, data as
follows is returned:
YAMON> dump -32 0xbf000900 0x40
BF000900: 1F000942 1F000942 1F000900 1F000900 ...B...B........
BF000910: 1F000901 1F000901 1F000900 1F000900 ................
BF000920: 1F000900 1F000900 1F000960 1F000960 ...........`...`
BF000930: 1F000900 1F000900 1F0009FF 1F0009FF ................
YAMON>
Evidently high-order 24 bits return values previously driven in the
address phase (the 3 highest order address bits used with the command
above are masked out in the simple virtual address mapping used here and
come out at zeros on the external bus), a common scenario with bus lines
left floating, due to bus capacitance.
Consequently when the value of IIR, mapped at 0x1f000910, is retrieved
in `autoconfig', it comes out at 0x1f0009c1 and when it is right-shifted
by 6 and then assigned to 8-bit `scratch' variable, the value calculated
is 0x27, not one of 0, 1, 2, 3 expected in port type determination.
Fix the issue then, by assigning the value returned from `serial_in' to
`scratch' first, which masks out 24 high-order bits retrieved, and only
then right-shift the resulting 8-bit data quantity, producing the value
of 3 in this case, as expected. Fix the same issue in `serial_dl_read'.
The problem first appeared with Linux 2.6.9-rc3 which predates our repo
history, but the origin could be identified with the old MIPS/Linux repo
also at: <git://git.kernel.org/pub/scm/linux/kernel/git/ralf/linux.git>
as commit e0d2356c0777 ("Merge with Linux 2.6.9-rc3."), where code in
`serial_in' was updated with this case:
+ case UPIO_MEM32:
+ return readl(up->port.membase + offset);
+
which made it produce results outside the unsigned 8-bit range for the
first time, though obviously it is system dependent what actual values
appear in the high order bits retrieved and it may well have been zeros
in the relevant positions with the system the change originally was
intended for. It is at that point that code in `autoconf' should have
been updated accordingly, but clearly it was overlooked.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org # v2.6.12+
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260516220.37803@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c4a509d3815a260c423c0633bd73695250ac26d upstream.
Fix uart corruption issue when rx power off.
Add spin lock in mtk8250_dma_rx_complete function in APDMA mode.
when uart is used as a communication port with external device(GPS).
when external device(GPS) power off, the power of rx pin is also from
1.8v to 0v. Even if there is not any data in rx. But uart rx pin can
capture the data "0".
If uart don't receive any data in specified cycle, uart will generates
BI(Break interrupt) interrupt.
If external device(GPS) power off, we found that BI interrupt appeared
continuously and very frequently.
When uart interrupt type is BI, uart IRQ handler(8250 framwork
API:serial8250_handle_irq) will push data to tty buffer.
mtk8250_dma_rx_complete is a task of mtk_uart_apdma_rx_handler.
mtk8250_dma_rx_complete priority is lower than uart irq
handler(serial8250_handle_irq).
if we are in process of mtk8250_dma_rx_complete, uart appear BI
interrupt:1)serial8250_handle_irq will priority execution.2)it may cause
write tty buffer conflict in mtk8250_dma_rx_complete.
So the spin lock protect the rx receive data process is not break.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210729084640.17613-2-zhiyong.tao@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fad92b11047a748c996ebd6cfb164a63814eeb2e ]
In the probe function, if the final 'serial_config()' fails, 'info' is
leaking.
Add a resource handling path to free this memory.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/dc25f96b7faebf42e60fe8d02963c941cf4d8124.1621971720.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b67e830d38fa9335d927fe67e812e3ed81b4689c ]
On K3 family of SoCs (which includes AM654 SoC), it is observed that RX
TIMEOUT is signalled after RX FIFO has been drained, in which case a
dummy read of RX FIFO is required to clear RX TIMEOUT condition.
Otherwise, this would lead to an interrupt storm.
Fix this by introducing UART_RX_TIMEOUT_QUIRK flag and doing a dummy
read in IRQ handler when RX TIMEOUT is reported with no data in RX FIFO.
Fixes: be70874498 ("serial: 8250_omap: Add support for AM654 UART controller")
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20210622145704.11168-1-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 439c7183e5b97952bba1747f5ffc4dea45a6a18b ]
UARTs on TI SoCs prior to J7200 don't provide independent control over
RX FIFO not empty interrupt (RHR_IT) and RX timeout interrupt.
Starting with J7200 SoC, its possible to disable RHR_IT independent of
RX timeout interrupt using bit 2 of IER2 register. So disable RHR_IT
once RX DMA is started so as to avoid spurious interrupt being raised
when data is in the RX FIFO but is yet to be drained by DMA (a known
errata in older SoCs).
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20201029051930.7097-1-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78bcae8616ac277d6cb7f38e211493948ed73e30 ]
Support for magic baud rate divisors of 32770 and 32769 used with SMSC
Super I/O chips for extra baud rates of 230400 and 460800 respectively
where base rate is 115200[1] has been added around Linux 2.5.64, which
predates our repo history, but the origin could be identified as commit
2a717aad772f ("Merge with Linux 2.5.64.") with the old MIPS/Linux repo
also at: <git://git.kernel.org/pub/scm/linux/kernel/git/ralf/linux.git>.
Code that is now in `serial8250_do_get_divisor' was added back then to
`serial8250_get_divisor', but that code would only ever trigger if one
of the higher baud rates was actually requested, and that cannot ever
happen, because the earlier call to `serial8250_get_baud_rate' never
returns them. This is because it calls `uart_get_baud_rate' with the
maximum requested being the base rate, that is clk/16 or 115200 for SMSC
chips at their nominal clock rate.
Fix it then and allow UPF_MAGIC_MULTIPLIER baud rates to be selected, by
requesting the maximum baud rate of clk/4 rather than clk/16 if the flag
has been set. Also correct the minimum baud rate, observing that these
ports only support actual (non-magic) divisors of up to 32767 only.
References:
[1] "FDC37M81x, PC98/99 Compliant Enhanced Super I/O Controller with
Keyboard/Mouse Wake-Up", Standard Microsystems Corporation, Rev.
03/27/2000, Table 31 - "Baud Rates", p. 77
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2105190412280.29169@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7e325aaa8c3593b5a572b583ecad79e95f32e7f ]
This loop ends on -1 so the error message will never be printed.
Fixes: 4bcf59a5de ("serial: 8250: 8250_omap: Account for data in flight during DMA teardown")
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YIpd+kOpXKMpEXPf@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 11b1d881a90fc184cc7d06e9804eb288c24a2a0d upstream.
The GLOBETROTTER.cis entry in serial_cs matches more devices than
intended and breaks them. Remove it.
Example: # pccardctl info
PRODID_1="Option International
"
PRODID_2="GSM-Ready 56K/ISDN
"
PRODID_3="021
"
PRODID_4="A
"
MANFID=0013,0000
FUNCID=0
result:
pcmcia 0.0: Direct firmware load for cis/GLOBETROTTER.cis failed with error -2
The GLOBETROTTER.cis is nowhere to be found. There's GLOBETROTTER.cis.ihex at
https://netdev.vger.kernel.narkive.com/h4inqdxM/patch-axnet-cs-fix-phy-id-detection-for-bogus-asix-chip#post41
It's from completely diffetent card:
vers_1 4.1, "Option International", "GSM/GPRS GlobeTrotter", "001", "A"
Signed-off-by: Ondrej Zary <linux@zary.sk>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210611201940.23898-1-linux@zary.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9808f9be31c68af43f6e531f2c851ebb066513fe upstream.
In commit 8428413b1d ("serial: 8250_pci: Implement MSI(-X) support")
the way the irq gets allocated was changed. With that change the
handling FL_NOIRQ got lost. Restore the old behaviour.
Fixes: 8428413b1d ("serial: 8250_pci: Implement MSI(-X) support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Link: https://lore.kernel.org/r/20210527095529.26281-1-christian.gmeiner@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e0e24208792080135248f23fdf6d51aa2e04df05 upstream.
Add support for new HPE serial device. It is MSI enabled,
but otherwise similar to legacy HP server serial devices.
Tested-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Randy Wright <rwright@hpe.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1621009614-28836-1-git-send-email-rwright@hpe.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c35d2a960c0077a4cb09bf4989f45d289332ea0 upstream.
Add device HID AMDI0022 to the AMD UART controller driver match table
and create a platform device for it. This controller can be found on
Microsoft Surface Laptop 4 devices and seems similar enough that we can
just copy the existing AMDI0020 entries.
Cc: <stable@vger.kernel.org> # 5.10+
Tested-by: Sachi King <nakato@nakato.io>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com> # for 8250_dw part
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20210512210413.1982933-1-luzmaximilian@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df8f2be2fd0b44b2cb6077068f52e05f0ac40897 upstream.
Aspeed Virtual UARTs directly bridge e.g. the system console UART on the
LPC bus to the UART interface on the BMC's internal APB. As such there's
no RS-232 signalling involved - the UART interfaces on each bus are
directly connected as the producers and consumers of the one set of
FIFOs.
The APB in the AST2600 generally runs at 100MHz while the LPC bus peaks
at 33MHz. The difference in clock speeds exposes a race in the VUART
design where a Tx data burst on the APB interface can result in a byte
lost on the LPC interface. The symptom is LSR[DR] remains clear on the
LPC interface despite data being present in its Rx FIFO, while LSR[THRE]
remains clear on the APB interface as the host has not consumed the data
the BMC has transmitted. In this state, the UART has stalled and no
further data can be transmitted without manual intervention (e.g.
resetting the FIFOs, resulting in loss of data).
The recommended work-around is to insert a read cycle on the APB
interface between writes to THR.
Cc: ChiaWei Wang <chiawei_wang@aspeedtech.com>
Tested-by: ChiaWei Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210520021334.497341-2-andrew@aj.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6e4e636e0e3e0b5deffc5e233adcb2cd4e68f2d0 ]
The pm_runtime_enable will increase power disable depth.
Thus a pairing decrement is needed on the error handling
path to keep it balanced according to context.
Fixes: e32a83c70c ("serial: 8250-mtk: modify mtk uart power and clock management")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201119141126.168850-1-zhangqilong3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d96f04d347e4011977abdbb4da5d8f303ebd26f8 upstream.
It has been observed that once per 300-1300 port openings the first
transmitted byte is being corrupted on AM3352 ("v" written to FIFO appeared
as "e" on the wire). It only happened if single byte has been transmitted
right after port open, which means, DMA is not used for this transfer and
the corruption never happened afterwards.
Therefore I've carefully re-read the MDR1 errata (link below), which says
"when accessing the MDR1 registers that causes a dummy under-run condition
that will freeze the UART in IrDA transmission. In UART mode, this may
corrupt the transferred data". Strictly speaking,
omap_8250_mdr1_errataset() performs a read access and if the value is the
same as should be written, exits without errata-recommended FIFO reset.
A brief check of the serial_omap_mdr1_errataset() from the competing
omap-serial driver showed it has no read access of MDR1. After removing the
read access from omap_8250_mdr1_errataset() the data corruption never
happened any more.
Link: https://www.ti.com/lit/er/sprz360i/sprz360i.pdf
Fixes: 61929cf016 ("tty: serial: Add 8250-core based omap driver")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20201210055257.1053028-1-alexander.sverdlin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mediatek 8250 port supports speed higher than uartclk / 16. If the baud
rates in both the new and the old termios setting are higher than
uartclk / 16, the WARN_ON in uart_get_baud_rate() will be triggered.
Passing NULL as the old termios so uart_get_baud_rate() will use
uartclk / 16 - 1 as the new baud rate which will be replaced by the
original baud rate later by tty_termios_encode_baud_rate() in
mtk8250_set_termios().
Fixes: 551e553f0d ("serial: 8250_mtk: Fix high-speed baud rates clamping")
Signed-off-by: Claire Chang <tientzu@chromium.org>
Link: https://lore.kernel.org/r/20201102120749.374458-1-tientzu@chromium.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has been discovered that there is a potential deadlock between
the clock-change-notifier thread and the UART port suspending one:
CPU0 (suspend CPU/UART) CPU1 (update clock)
---- ----
lock(&port->mutex);
lock((work_completion)(&data->clk_work));
lock(&port->mutex);
lock((work_completion)(&data->clk_work));
*** DEADLOCK ***
The best way to fix this is to eliminate the CPU0
port->mutex/work-completion scenario. So we suggest to register and
unregister the clock-notifier during the DW APB UART port probe/remove
procedures, instead of doing that at the points of the port
startup/shutdown.
Link: https://lore.kernel.org/linux-serial/f1cd5c75-9cda-6896-a4e2-42c5bfc3f5c3@redhat.com
Fixes: cc816969d7 ("serial: 8250_dw: Fix common clocks usage race condition")
Reported-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200923161950.6237-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is erroneous to update the TTY port baud rate if it hasn't been
initialized yet, because in that case the TTY struct isn't set. So there
is no termios structure to get and re-calculate the baud if the current
baud can't be reached. Let's skip the baud rate update then until the port
is fully initialized.
Note the update UART clock method still sets the uartclk member with a new
ref clock value even if the port is turned off. The new UART ref clock
rate will be used later on the port starting up procedure.
Fixes: 868f3ee6e4 ("serial: 8250: Add 8250 port clock update method")
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200923161950.6237-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has been a mistake to add the MCR register RTS/DTS fields setting in
the generic method of the UART reference clock update. There is no point
in asserting these lines at that procedure. Just discard the
serial8250_out_MCR() mathod invocation from there then.
Fixes: 868f3ee6e4 ("serial: 8250: Add 8250 port clock update method")
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200923161950.6237-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the port of the commit db1b5bc047 ("serial: 8250: Fix TX
interrupt handling condition") to the 8250_fsl irq handling logic.
Interrupt handler checked THRE bit (transmitter holding register
empty) in LSR to detect if TX fifo is empty.
In case when there is only receive interrupts the TX handling
got called because THRE bit in LSR is set when there is no
transmission (FIFO empty). TX handling caused TX stop, which in
RS-485 half-duplex mode actually resets receiver FIFO. This is not
desired during reception because of possible data loss.
The fix is to check if THRI is set in IER in addition of the TX
fifo status. THRI in IER is set when TX is started and cleared
when TX is stopped.
This ensures that TX handling is only called when there is really
transmission on going and an interrupt for THRE and not when there
are only RX interrupts.
Signed-off-by: Andrij Abyzov <aabyzov@slb.com>
Link: https://lore.kernel.org/r/20200928144127.87156-1-aabyzov@slb.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the tty/serial fixes in here and this resolves a merge issue in
the 8250 driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To use mmio32, we also need to set regshift.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Acked-by: Eddie Huang <eddie.huang@mediatek.com>
Link: https://lore.kernel.org/r/20200915054825.3289105-2-hsinyi@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds support for ACPI enumerated FSL 16550 UARTs.
For supporting ACPI, I added a wrapper so that this driver
can be used if firmware has exposed the HID "NXP0018" in
DSDT table.
This will be built as object file if config "SERIAL_8250_FSL"
is enabled which depends on config "SERIAL_8250_CONSOLE".
Signed-off-by: kuldip dwivedi <kuldip.dwivedi@puresoftware.com>
Link: https://lore.kernel.org/r/20200903113402.12371-1-kuldip.dwivedi@puresoftware.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/20200901153100.18827-1-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl9ML+IeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGA8EIAIy/kTbFS0yrE9yV
hb98oX0z9+EU9YQg9vhaRWwPd+rJF/JMQZLqYcwbhjG9abaUL3T3fEcSAefMHw8E
LAt+hYzA38dHt7tqhsFQX3vV1VorvDVICBVN0yRPRWKKikq4OPIHzaAR9tleGAF5
8btQisl1PjN+obwYmLuNb6aX16OCwAF+uXOwehcoJs9dvMNhwtXRzfOflWzOvOo6
tE0bHErlylLDfLv4ZzEfczTdks4QJZ7C0xLSf3oN9AAynW42Xnhct4hi8qZY/hCf
CMaqeN4hdpub6TvQIqBdDqMMjEXGFgeNSnAEBQY9VpvUqz8NTu6sQxwgJEKDF5tg
d81lv2c=
=uW/F
-----END PGP SIGNATURE-----
Merge 5.9-rc3 into tty-next
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Maciej W. Rozycki