Remove the data pointer from struct nf_queue_handler. It has never been used
and is useless for the only handler that really matters, nfnetlink_queue,
since the handler is shared between all instances.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
nf_conntrack_h323 needs ip6_route_output for the call forwarding filter.
Add a ->route function to nf_afinfo and use that to avoid pulling in the
ipv6 module.
Fix the #ifdef for the IPv6 code while I'm at it - the IPv6 support is
only needed when IPv6 conntrack is enabled.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add rate estimator match. The rate estimator match can match on
estimated rates by the RATEEST target. It supports matching on
absolute bps/pps values, comparing two rate estimators and matching
on the difference between two rate estimators.
This is what I use to route outgoing data connections from a FTP
server over two lines based on the available bandwidth:
# estimate outgoing rates
iptables -t mangle -A POSTROUTING -o eth0 -j RATEEST --rateest-name eth0 \
--rateest-interval 250ms \
--rateest-ewma 0.5s
iptables -t mangle -A POSTROUTING -o ppp0 -j RATEEST --rateest-name ppp0 \
--rateest-interval 250ms \
--rateest-ewma 0.5s
# mark based on available bandwidth
iptables -t mangle -A BALANCE -m state --state NEW \
-m helper --helper ftp \
-m rateest --rateest-delta \
--rateest1 eth0 \
--rateest-bps1 2.5mbit \
--rateest-gt \
--rateest2 ppp0 \
--rateest-bps2 2mbit \
-j CONNMARK --set-mark 0x1
iptables -t mangle -A BALANCE -m state --state NEW \
-m helper --helper ftp \
-m rateest --rateest-delta \
--rateest1 ppp0 \
--rateest-bps1 2mbit \
--rateest-gt \
--rateest2 eth0 \
--rateest-bps2 2.5mbit \
-j CONNMARK --set-mark 0x2
iptables -t mangle -A BALANCE -j CONNMARK --restore-mark
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new rate estimator target (using gen_estimator). In combination with
the rateest match (next patch) this can be used for load-based multipath
routing.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extends the xt_DSCP target by xt_TOS v1 to add support for selectively
setting and flipping any bit in the IPv4 TOS and IPv6 Priority fields.
(ipt_TOS and xt_DSCP only accepted a limited range of possible
values.)
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extends the xt_dscp match by xt_tos v1 to add support for selectively
matching any bit in the IPv4 TOS and IPv6 Priority fields. (ipt_tos
and xt_dscp only accepted a limited range of possible values.)
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Addrtype match has a new revision (1), which lets address type checking
limited to the interface the current packet belongs to. Either incoming
or outgoing interface can be used depending on the current hook. In the
FORWARD hook two maches should be used if both interfaces have to be checked.
The new structure is ipt_addrtype_info_v1.
Revision 0 lets older userspace programs use the match as earlier.
ipt_addrtype_info is used.
Signed-off-by: Laszlo Attila Toth <panther@balabit.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
xt_owner merges ipt_owner and ip6t_owner, and adds a flag to match
on socket (non-)existence.
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a big array of NR_CPUS entries, we can compute the size
needed at runtime, using nr_cpu_ids
This should save some ram (especially on David's machines where NR_CPUS=4096 :
32 KB can be saved per table, and 64KB for dynamically allocated ones (because
of slab/slub alignements) )
In particular, the 'bootstrap' tables are not any more static (in data
section) but on stack as their size is now very small.
This also should reduce the size used on stack in compat functions
(get_info() declares an automatic variable, that could be bigger than kernel
stack size for big NR_CPUS)
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sven Schnelle <svens@bitebene.org>
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the basic infrastructure for per namespace sysctls.
A list of lists of sysctl headers is added, allowing each namespace to have
it's own list of sysctl headers.
Each list of sysctl headers has a lookup function to find the first
sysctl header in the list, allowing the lists to have a per namespace
instance.
register_sysct_root is added to tell sysctl.c about additional
lists of sysctl_headers. As all of the users are expected to be in
kernel no unregister function is provided.
sysctl_head_next is updated to walk through the list of lists.
__register_sysctl_paths is added to add a new sysctl table on
a non-default sysctl list.
The only intrusive part of this patch is propagating the information
to decided which list of sysctls to use for sysctl_check_table.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Serge Hallyn <serue@us.ibm.com>
Cc: Daniel Lezcano <dlezcano@fr.ibm.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
By doing this we allow users of register_sysctl_paths that build
and dynamically allocate their ctl_table to be simpler. This allows
them to just remember the ctl_table_header returned from
register_sysctl_paths from which they can now find the
ctl_table array they need to free.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Serge Hallyn <serue@us.ibm.com>
Cc: Daniel Lezcano <dlezcano@fr.ibm.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a number of modules that register a sysctl table
somewhere deeply nested in the sysctl hierarchy, such as
fs/nfs, fs/xfs, dev/cdrom, etc.
They all specify several dummy ctl_tables for the path name.
This patch implements register_sysctl_path that takes
an additional path name, and makes up dummy sysctl nodes
for each component.
This patch was originally written by Olaf Kirch and
brought to my attention and reworked some by Olaf Hering.
I have changed a few additional things so the bugs are mine.
After converting all of the easy callers Olaf Hering observed
allyesconfig ARCH=i386, the patch reduces the final binary size by 9369 bytes.
.text +897
.data -7008
text data bss dec hex filename
26959310 4045899 4718592 35723801 2211a19 ../vmlinux-vanilla
26960207 4038891 4718592 35717690 221023a ../O-allyesconfig/vmlinux
So this change is both a space savings and a code simplification.
CC: Olaf Kirch <okir@suse.de>
CC: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Serge Hallyn <serue@us.ibm.com>
Cc: Daniel Lezcano <dlezcano@fr.ibm.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kill the defines again, convert to the new checksum helper names and
remove the dependency of NET_ACT_NAT on NETFILTER.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows to get rid of the CONFIG_NETFILTER dependency of NET_ACT_NAT.
This patch redefines the old names to keep the noise low, the next patch
converts all users.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the necessary state transitions for the two forms of passive-close
* PASSIVE_CLOSE - which is entered when a host receives a Close;
* PASSIVE_CLOSEREQ - which is entered when a client receives a CloseReq.
Here is a detailed account of what the patch does in each state.
1) Receiving CloseReq
The pseudo-code in 8.5 says:
Step 13: Process CloseReq
If P.type == CloseReq and S.state < CLOSEREQ,
Generate Close
S.state := CLOSING
Set CLOSING timer.
This means we need to address what to do in CLOSED, LISTEN, REQUEST, RESPOND, PARTOPEN, and OPEN.
* CLOSED: silently ignore - it may be a late or duplicate CloseReq;
* LISTEN/RESPOND: will not appear, since Step 7 is performed first (we know we are the client);
* REQUEST: perform Step 13 directly (no need to enqueue packet);
* OPEN/PARTOPEN: enter PASSIVE_CLOSEREQ so that the application has a chance to process unread data.
When already in PASSIVE_CLOSEREQ, no second CloseReq is enqueued. In any other state, the CloseReq is ignored.
I think that this offers some robustness against rare and pathological cases: e.g. a simultaneous close where
the client sends a Close and the server a CloseReq. The client will then be retransmitting its Close until it
gets the Reset, so ignoring the CloseReq while in state CLOSING is sane.
2) Receiving Close
The code below from 8.5 is unconditional.
Step 14: Process Close
If P.type == Close,
Generate Reset(Closed)
Tear down connection
Drop packet and return
Thus we need to consider all states:
* CLOSED: silently ignore, since this can happen when a retransmitted or late Close arrives;
* LISTEN: dccp_rcv_state_process() will generate a Reset ("No Connection");
* REQUEST: perform Step 14 directly (no need to enqueue packet);
* RESPOND: dccp_check_req() will generate a Reset ("Packet Error") -- left it at that;
* OPEN/PARTOPEN: enter PASSIVE_CLOSE so that application has a chance to process unread data;
* CLOSEREQ: server performed active-close -- perform Step 14;
* CLOSING: simultaneous-close: use a tie-breaker to avoid message ping-pong (see comment);
* PASSIVE_CLOSEREQ: ignore - the peer has a bug (sending first a CloseReq and now a Close);
* TIMEWAIT: packet is ignored.
Note that the condition of receiving a packet in state CLOSED here is different from the condition "there
is no socket for such a connection": the socket still exists, but its state indicates it is unusable.
Last, dccp_finish_passive_close sets either DCCP_CLOSED or DCCP_CLOSING = TCP_CLOSING, so that
sk_stream_wait_close() will wait for the final Reset (which will trigger CLOSING => CLOSED).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds two auxiliary states to deal with passive closes:
* PASSIVE_CLOSE (reached from OPEN via reception of Close) and
* PASSIVE_CLOSEREQ (reached from OPEN via reception of CloseReq)
as internal intermediate states.
These states are used to allow a receiver to process unread data before
acknowledging the received connection-termination-request (the Close/CloseReq).
Without such support, it will happen that passively-closed sockets enter CLOSED
state while there is still unprocessed data in the queue; leading to unexpected
and erratic API behaviour.
PASSIVE_CLOSE has been mapped into TCPF_CLOSE_WAIT, so that the code will
seamlessly work with inet_accept() (which tests for this state).
The state names are thanks to Arnaldo, who suggested this naming scheme
following an earlier revision of this patch.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch includes support for the Intra-Site Automatic Tunnel
Addressing Protocol (ISATAP) per RFC4214. It uses the SIT
module, and is configured using extensions to the "iproute2"
utility. The diffs are specific to the Linux 2.6.24-rc2 kernel
distribution.
This version includes the diff for ./include/linux/if.h which was
missing in the v2.4 submission and is needed to make the
patch compile. The patch has been installed, compiled and
tested in a clean 2.6.24-rc2 kernel build area.
Signed-off-by: Fred L. Templin <fred.l.templin@boeing.com>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sock_wake_async() performs a bit different actions
depending on "how" argument. Unfortunately this argument
ony has numerical magic values.
I propose to give names to their constants to help people
reading this function callers understand what's going on
without looking into this function all the time.
I suppose this is 2.6.25 material, but if it's not (or the
naming seems poor/bad/awful), I can rework it against the
current net-2.6 tree.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
I keep getting this build error and couldn't find anyone fixing
it in archives. ...Maybe all net developers except me build
just SMP kernels :-).
In file included from include/net/sock.h:50,
from ipc/mqueue.c:35:
include/linux/pcounter.h: In function 'pcounter_add':
include/linux/pcounter.h:87: error: 'struct pcounter' has no
member named 'value'
make[1]: *** [ipc/mqueue.o] Error 1
make: *** [ipc] Error 2
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This decouples PARTOPEN from TCP-specific stream-states.
It thus addresses the FIXME.
The code has been checked with regard to dependency on PARTOPEN and FIN_WAIT1
states (to which PARTOPEN previously was mapped): there is no difference, as
PARTOPEN is always referred to directly (i.e. not via the mapping to TCP
state).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This just generalises what was introduced by Eric Dumazet for the struct proto
inuse field in 286ab3d46058840d68e5d7d52e316c1f7e98c59f:
[NET]: Define infrastructure to keep 'inuse' changes in an efficent SMP/NUMA way.
Please look at the comment in there to see the rationale.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds several structs and definitions to ieee80211.h
to support 802.11n draft specifications.
As 802.11n depends on and extends the 802.11e standard in several issues,
there are also several definitions that belong to 802.11e.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After this patch none of the netlink callback support anything
except the initial network namespace but the rtnetlink infrastructure
now handles multiple network namespaces.
Changes from v2:
- IPv6 addrlabel processing
Changes from v1:
- no need for special rtnl_unlock handling
- fixed IPv6 ndisc
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds IEEE80211_MAX_FRAME_LEN which is useful for drivers trying
to determine how much to allocate for their RX buffers.
It also updates the comment on IEEE80211_MAX_DATA_LEN based on revisions
in 802.11e.
IEEE80211_MAX_FRAG_THRESHOLD and IEEE80211_MAX_RTS_THRESHOLD are also
revised due to the new maximum frame size.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx_flags variable is redundant. Turning rx on/off is done
via setting the rx_np pointer.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The local_mac is managed by the network device, no need to keep a
spare copy and all the management problems that could cause.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the missing Kbuild entries and the missing Kbuild file
in include/linux/can for the CAN subsystem.
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the use of plain integers instead of __u32 in a struct
that is visible from kernel space and user space.
Thanks to Sam Ravnborg for pointing out the wrong plain int usage.
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the CAN broadcast manager (bcm) protocol.
Signed-off-by: Oliver Hartkopp <oliver.hartkopp@volkswagen.de>
Signed-off-by: Urs Thuermann <urs.thuermann@volkswagen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the CAN raw protocol.
Signed-off-by: Oliver Hartkopp <oliver.hartkopp@volkswagen.de>
Signed-off-by: Urs Thuermann <urs.thuermann@volkswagen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the CAN core functionality but no protocols or drivers.
No protocol implementations are included here. They come as separate
patches. Protocol numbers are already in include/linux/can.h.
Signed-off-by: Oliver Hartkopp <oliver.hartkopp@volkswagen.de>
Signed-off-by: Urs Thuermann <urs.thuermann@volkswagen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a protocol/address family number, ARP hardware type,
ethernet packet type, and a line discipline number for the SocketCAN
implementation.
Signed-off-by: Oliver Hartkopp <oliver.hartkopp@volkswagen.de>
Signed-off-by: Urs Thuermann <urs.thuermann@volkswagen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Key points of this patch are:
- In case new SACK information is advance only type, no skb
processing below previously discovered highest point is done
- Optimize cases below highest point too since there's no need
to always go up to highest point (which is very likely still
present in that SACK), this is not entirely true though
because I'm dropping the fastpath_skb_hint which could
previously optimize those cases even better. Whether that's
significant, I'm not too sure.
Currently it will provide skipping by walking. Combined with
RB-tree, all skipping would become fast too regardless of window
size (can be done incrementally later).
Previously a number of cases in TCP SACK processing fails to
take advantage of costly stored information in sack_recv_cache,
most importantly, expected events such as cumulative ACK and new
hole ACKs. Processing on such ACKs result in rather long walks
building up latencies (which easily gets nasty when window is
huge). Those latencies are often completely unnecessary
compared with the amount of _new_ information received, usually
for cumulative ACK there's no new information at all, yet TCP
walks whole queue unnecessary potentially taking a number of
costly cache misses on the way, etc.!
Since the inclusion of highest_sack, there's a lot information
that is very likely redundant (SACK fastpath hint stuff,
fackets_out, highest_sack), though there's no ultimate guarantee
that they'll remain the same whole the time (in all unearthly
scenarios). Take advantage of this knowledge here and drop
fastpath hint and use direct access to highest SACKed skb as
a replacement.
Effectively "special cased" fastpath is dropped. This change
adds some complexity to introduce better coveraged "fastpath",
though the added complexity should make TCP behave more cache
friendly.
The current ACK's SACK blocks are compared against each cached
block individially and only ranges that are new are then scanned
by the high constant walk. For other parts of write queue, even
when in previously known part of the SACK blocks, a faster skip
function is used (if necessary at all). In addition, whenever
possible, TCP fast-forwards to highest_sack skb that was made
available by an earlier patch. In typical case, no other things
but this fast-forward and mandatory markings after that occur
making the access pattern quite similar to the former fastpath
"special case".
DSACKs are special case that must always be walked.
The local to recv_sack_cache copying could be more intelligent
w.r.t DSACKs which are likely to be there only once but that
is left to a separate patch.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is going to replace the sack fastpath hint quite soon... :-)
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Policy table is implemented as an RCU linear list since we do not expect
large list nor frequent updates.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IPv4 and IPv6 hook values are identical, yet some code tries to figure
out the "correct" value by looking at the address family. Introduce NF_INET_*
values for both IPv4 and IPv6. The old values are kept in a #ifndef __KERNEL__
section for userspace compatibility.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow caller to pass in a release function, there might be
other resources that need releasing as well. Needed for
network receive.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (24 commits)
HID: ADS/Tech Radio si470x needs blacklist entry
HID: Logitech Extreme 3D needs NOGET quirk
HID: Refactor MS Presenter 8K key mapping
HID: MS Presenter mapping for PID 0x0701
HID: Support Samsung IR remote
HID: fix compilation of hidbp drivers without usbhid
HID: Blacklist the Gretag-Macbeth Huey display colorimeter
HID: the `bit' in hidinput_mapping_quirks() is an out parameter
HID: remove redundant WARN_ON()s in order not to scare users
HID: force hiddev creation for SONY PS3 controller
HID: Use hid blacklist in usbmouse/usbkbd
HID: proper handling of MS 4k and 6k devices
HID: remove unused variable in quirk event handler
HID: hid-input quirk for BTC 8193
HID: separate hid-input event quirks from generic code
HID: refactor mapping to input subsystem for quirky devices
HID: Microsoft Wireless Optical Desktop 3.0 quirk
HID: Add support for Logitech Elite keyboards
HID: add full support for Genius KB-29E
HID: fix a potential bug in pointer casting
...
* 'sg' of git://git.kernel.dk/linux-2.6-block:
SG: work with the SCSI fixed maximum allocations.
SG: Convert SCSI to use scatterlist helpers for sg chaining
SG: Move functions to lib/scatterlist.c and add sg chaining allocator helpers
Samsung USB remotes (0419:0001) are rejected by kernel 2.6.23, because the
report descriptor from the remote contains a 48 bit HID report field. HID 1.11
states: Fields may span at most 4 bytes.
This patch, based on 2.6.23, fixes this by modifying the internal report
descriptor in hid-quirks.c. Additional user space support (e.g. LIRC) is
required to fetch the information from the hiddev interface.
The burden to reconstruct the data is moved into userspace (lirc through hiddev).
There is no need to set HID_QUIRK_HIDDEV quirk, as the device has also output
applications, which trigger the creation of hiddev device automatically.
Signed-off-by: Robert Schedel <r.schedel@yahoo.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix a panic, by changing
hidinput_mapping_quirks(,, unsigned long *bit,)
to
hidinput_mapping_quirks(,, unsigned long **bit,)
The `bit' in this function is an out parameter.
Signed-off-by: Fengguang Wu <wfg@mail.ustc.edu.cn>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This removes ugly macros IS_* to distinguish devices that
need special handling in hid-input, and establish proper
quirks for them.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
BTC 8193 keyboard handles its scrollwheel in very non-standard way.
It produces two non-standard usages for scrolling up and down, in
both cases with postive value equaling to 1. We handle this by temporary
mapping, which we then catch in quirk event handler, and remap to
negative HWHEEL even in order to introduce correct behavior.
Also the button requires special mapping, as it triggers standard-violating
usage code.
Reported in kernel.org bugzilla #9385
Reported-by: Kir Kolyshkin <kir@sacred.ru>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch separates also the hid-input quirks that have to be
applied at the time the event occurs, so that the generic code
handling HUT-compliant devices is not messed up by them too much.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently, the handling of mapping between hid and input for devices
that don't conform to HUT 1.12 specification is very messy -- no per-device
handling, no blacklists, conditions on idVendor and idProduct placed
all over the code.
This patch moves all the device-specific input mapping to a separate
file, and introduces a blacklist-style handling for non-standard
device-specific mappings.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Genius KB-29E has broken report descriptor, which causes some of the
Consumer usages to appear incorrectly as Button usages. We fix it by
fixing the report descriptor before it is being parsed.
Also a few of the keys violate the HUT standard, so they need a special
handling. They currently fall into "Reserved" range as per HUT 1.12.
Reported-by: Szekeres Istvan <szekeres@iii.hu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This mouse distinguishes horizontal wheel from vertical by a special "pseudo
event" GenericDesktop.00b8, with values of 0 for vertical and 8 for horizontal
wheel. Because this event is supplied by the parser too late, we need to delay
a wheel event, wait for this one and send either REL_WHEEL or REL_HWHEEL to
input depending on the event value.
Signed-off-by: Pavel Troller <patrol@sinus.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Preserve identifiers exposed in build and run time configuration though in
order not to break existing configurations.
This is in preparation for adding support for Apple aluminum USB keyboards.
Signed-off-by: Michel Daenzer <michel@tungstengraphics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* orion: (26 commits)
[ARM] Orion: implement power-off method for QNAP TS-109/209
[ARM] Orion: add support for QNAP TS-109/TS-209
[ARM] Orion: I2C support
[I2C] i2c-mv64xxx: Don't set i2c_adapter.retries
[I2C] Split mv643xx I2C platform support
[ARM] Orion: enable CONFIG_RTC_DRV_M41T80 for D-Link DNS-323
[ARM] Orion defconfig
[ARM] Orion: add support for Orion/MV88F5181 based D-Link DNS-323
[ARM] Orion: MV88F5181 support bits
[ARM] Orion: Buffalo/Revogear Kurobox Pro support
[ARM] OrionNAS RD board support
[ARM] Orion: support for Marvell Orion-2 (88F5281) Development Board
[ARM] Orion: common platform setup for Gigabit Ethernet port
[ARM] Orion: platform device registration for UART, USB and NAND
[ARM] Orion: system timer support
[ARM] Orion edge GPIO IRQ support
[ARM] Orion: IRQ support
[ARM] Orion: provide GPIO method for enabling hardware assisted blinking
[ARM] Orion: GPIO support
[ARM] Orion: programable address map support
...
Conflicts:
arch/arm/Kconfig
arch/arm/Makefile
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
SCSI sg table allocation has a maximum size (of SCSI_MAX_SG_SEGMENTS,
currently 128) and this will cause a BUG_ON() in SCSI if something
tries an allocation over it. This patch adds a size limit to the
chaining allocator to allow the specification of the maximum
allocation size for chaining, so we always chain in units of the
maximum SCSI allocation size.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
These DMA drain buffer implementations in drivers are pretty horrible
to do in terms of manipulating the scatterlist. Plus they're being
done at least in drivers/ide and drivers/ata, so we now have code
duplication.
The one use case for this, as I understand it is AHCI controllers doing
PIO mode to mmc devices but translating this to DMA at the controller
level.
So, what about adding a callback to the block layer that permits the
adding of the drain buffer for the problem devices. The idea is that
you'd do this in slave_configure after you find one of these devices.
The beauty of doing it in the block layer is that it quietly adds the
drain buffer to the end of the sg list, so it automatically gets mapped
(and unmapped) without anything unusual having to be done to the
scatterlist in driver/scsi or drivers/ata and without any alteration to
the transfer length.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
syslets (or other threads/processes that want io context sharing) can
set this to enforce sharing of io context.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The io context sharing introduced a per-ioc spinlock, that would protect
the cfq io context lookup. That is a regression from the original, since
we never needed any locking there because the ioc/cic were process private.
The cic lookup is changed from an rbtree construct to a radix tree, which
we can then use RCU to make the reader side lockless. That is the performance
critical path, modifying the radix tree is only done on process creation
(when that process first does IO, actually) and on process exit (if that
process has done IO).
As it so happens, radix trees are also much faster for this type of
lookup where the key is a pointer. It's a very sparse tree.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts 'uptodate' arguments of no longer exported
interfaces, end_that_request_first/last, to 'error', and removes
internal conversions for it in blk_end_request interfaces.
Also, this patch removes no longer needed end_io_error().
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch removes the following functions:
o end_that_request_first()
o end_that_request_chunk()
and stops exporting the functions below:
o end_that_request_last()
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch adds a variant of the interface, blk_end_bidi_request(),
which completes a bidi request.
Bidi request must be completed as a whole, both rq and rq->next_rq
at once. So the interface has 2 arguments for completion size.
As for ->end_io, only rq->end_io is called (rq->next_rq->end_io is not
called). So if special completion handling is needed, the handler
must be set to rq->end_io.
And the handler must take care of freeing next_rq too, since
the interface doesn't care of it if rq->end_io is not NULL.
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch adds a variant of the interface, blk_end_request_callback(),
which has driver callback feature.
Drivers may need to do special works between end_that_request_first()
and end_that_request_last().
For such drivers, blk_end_request_callback() allows it to pass
a callback function which is called between end_that_request_first()
and end_that_request_last().
This interface is only for fallback of other blk_end_request interfaces.
Drivers should avoid their tricky behaviors and use other interfaces
as much as possible.
Currently, only one driver, ide-cd, needs this interface.
So this interface should/will be removed, after the driver removes
such tricky behaviors.
o ide-cd (cdrom_newpc_intr())
In PIO mode, cdrom_newpc_intr() needs to defer end_that_request_last()
until the device clears DRQ_STAT and raises an interrupt after
end_that_request_first().
So end_that_request_first() and end_that_request_last() are called
separately in cdrom_newpc_intr().
This means blk_end_request_callback() has to return without
completing request even if no leftover in the request.
To satisfy the requirement, callback function has return value
so that drivers can tell blk_end_request_callback() to return
without completing request.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch adds/exports functions to get the size of request in bytes.
They are useful because blk_end_request interfaces take bytes
as a completed I/O size instead of sectors.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch adds 2 new interfaces for request completion:
o blk_end_request() : called without queue lock
o __blk_end_request() : called with queue lock held
blk_end_request takes 'error' as an argument instead of 'uptodate',
which current end_that_request_* take.
The meanings of values are below and the value is used when bio is
completed.
0 : success
< 0 : error
Some device drivers call some generic functions below between
end_that_request_{first/chunk} and end_that_request_last().
o add_disk_randomness()
o blk_queue_end_tag()
o blkdev_dequeue_request()
These are called in the blk_end_request interfaces as a part of
generic request completion.
So all device drivers become to call above functions.
To decide whether to call blkdev_dequeue_request(), blk_end_request
uses list_empty(&rq->queuelist) (blk_queued_rq() macro is added for it).
So drivers must re-initialize it using list_init() or so before calling
blk_end_request if drivers use it for its specific purpose.
(Currently, there is no driver which completes request without
re-initializing the queuelist after used it. So rq->queuelist
can be used for the purpose above.)
"Normal" drivers can be converted to use blk_end_request()
in a standard way shown below.
a) end_that_request_{chunk/first}
spin_lock_irqsave()
(add_disk_randomness(), blk_queue_end_tag(), blkdev_dequeue_request())
end_that_request_last()
spin_unlock_irqrestore()
=> blk_end_request()
b) spin_lock_irqsave()
end_that_request_{chunk/first}
(add_disk_randomness(), blk_queue_end_tag(), blkdev_dequeue_request())
end_that_request_last()
spin_unlock_irqrestore()
=> spin_lock_irqsave()
__blk_end_request()
spin_unlock_irqsave()
c) spin_lock_irqsave()
(add_disk_randomness(), blk_queue_end_tag(), blkdev_dequeue_request())
end_that_request_last()
spin_unlock_irqrestore()
=> blk_end_request() or spin_lock_irqsave()
__blk_end_request()
spin_unlock_irqrestore()
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Manually doing chained sg lists is not trivial, so add some helpers
to make sure that drivers get it right.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Let queue_dma_alignment return 0 if it was specifically set to 0.
This permits devices with no particular alignment restrictions to
use arbitrary user space buffers without copying.
Signed-off-by: Pete Wyckoff <pw@osc.edu>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Since the SCSI layer uses the request queues from the block layer, blktrace can
also be used to trace the requests to all SCSI devices (like SCSI tape drives),
not only disks. The only missing part is the ioctl interface to start and stop
tracing.
This patch adds the SETUP, START, STOP and TEARDOWN ioctls from blktrace to the
sg device files. With this change, blktrace can be used for SCSI devices like
for disks, e.g.: blktrace -d /dev/sg1 -o - | blkparse -i -
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This adds a i2c_new_dummy() primitive to help work with devices
that consume multiple addresses, which include many I2C eeproms
and at least one RTC.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The i2c_adapter.clients list of i2c_client nodes duplicates driver
model state. This patch starts removing that list, letting us remove
most existing users of those i2c-core lists.
* The core I2C code now iterates over the driver model's list instead
of the i2c-internal one in some places where it's safe:
- Passing a command/ioctl to each client, a mechanims
used almost exclusively by DVB adapters;
- Device address checking, in both i2c-core and i2c-dev.
* Provide i2c_verify_client() to use with driver model iterators.
* Flag the relevant i2c_adapter and i2c_client fields as deprecated,
to help prevent new users from appearing.
For the moment the list needs to stick around, since some issues show
up when deleting devices created by legacy I2C drivers. (They don't
follow standard driver model rules. Removing those devices can cause
self-deadlocks.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Discard all I2C driver IDs that aren't used anywhere. That's not just a
couple of them, but more like 49 or one quarter of all defined IDs! And
this is just a first pass, next will come all IDs that are set but
never used, or used but never set.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Move the tps65010 header file from the OMAP arch directory to the
more generic <linux/i2c/...> directory, and remove the spurious
dependency of this driver on OMAP.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
i2c_driver.list is superfluous, this list duplicates the one
maintained by the driver core. Drop it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
i2c_adapter.list is superfluous, this list duplicates the one
maintained by the driver core. Drop it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Use more standard prototypes for i2c_use_client() and
i2c_release_client(). The former now returns a pointer to the client,
and the latter no longer returns anything. This matches what all other
subsystems do.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
Don't implement our own reference counting mechanism for i2c clients
when the driver model already has one.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
This patch allows much of the I2C client address data to move from initdata
into text.
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch contains the overdue removal of three I2C drivers.
[JD: In fact only i2c-ixp4xx can be removed at the moment, the other two
platforms don't implement the generic GPIO layer yet.]
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch contains the scheduled removal of legacy I2C RTC drivers with
replacement drivers.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Based on the earlier work by Tejun Heo.
All users are gone so we can finally remove it.
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Based on the earlier work by Tejun Heo.
Switch set_xfer_rate() to use REQ_TYPE_ATA_TASKFILE requests
and make ide_wait_cmd() static.
There should be no functionality changes caused by this patch.
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use wait_drive_not_busy() in drive_cmd_intr().
v2:
* Fix wait_drive_not_busy() comment (noticed by Sergei).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
task_end_request() modified to always call ide_end_drive_cmd()
for taskfile requests. Previously, ide_end_drive_cmd() was
called only when IDE_TFLAG_FLAGGED was set. Also,
ide_dma_intr() is modified to use task_end_request().
Enables TASKFILE ioctls to get valid register outputs on
successful completion.
Bart:
- ported it over recent IDE changes
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_TFLAG_{HOB,TF,DEVICE} defines.
* Set IDE_TFLAG_IN_* flags in {do_rw,ide_no_data,ide_raw}_taskfile() users.
* Remove no longer needed ->tf_flags setup from ide_end_drive_cmd().
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
In ide_taskfile_ioctl(), there was a race condition involving
drive->io_32bit. It was cleared and restored during ioctl
requests but there was no synchronization with other requests.
So, other requests could execute with the altered ->io_32bit
setting or updated drive->io_32bit could be overwritten by
ide_taskfile_ioctl().
This patch adds IDE_TFLAG_IO_16BIT flag to indicate to
ide_pio_datablock() that 16-bit I/O is needed regardless of
drive->io_32bit settting.
Bart:
- ported it over recent IDE changes
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove broken disk byte-swapping support:
- it can cause a data corruption on SMP (or if using PREEMPT on UP)
- all data coming from disk are byte-swapped by taskfile_*_data() which
results in incorrect identify data being reported by /proc/ide/ and IOCTLs
- "hdx=bswap/byteswap" kernel parameter has been broken on m68k host drivers
(including Atari/Q40 ones) since 2.5.x days (because of 'hwif' zero-ing)
- byte-swapping is limited to PIO transfers (for working with TiVo disks on
x86 machines using user-space solutions or dm-byteswap should result in
much better performance because DMA can be used)
For previous discussions please see:
http://www.ussg.iu.edu/hypermail/linux/kernel/0201.0/0768.htmlhttp://lkml.org/lkml/2004/2/28/111
[ I have dm-byteswap device mapper target if somebody is interested
(patch is for 2.6.4 though but I'll dust it off if needed). ]
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Make remaining built-in only IDE host drivers modular, add ide-scan-pci.c
file for probing PCI host drivers registered with IDE core (special case
for built-in IDE and CONFIG_IDEPCI_PCIBUS_ORDER=y) and then take care of
the ordering in which all IDE host drivers are probed when IDE is built-in
during link time.
* Move probing of gayle, falconide, macide, q40ide and buddha (m68k arch
specific) host drivers, before PCI ones (no PCI on m68k), ide-cris (cris
arch specific), cmd640 (x86 arch specific) and pmac (ppc arch specific).
* Move probing of ide-cris (cris arch specific) host driver before cmd640
(x86 arch specific).
* Move probing of mpc8xx (ppc specific) host driver before ide-pnp (depends
on ISA and none of ppc platform that use mpc8xx supports ISA) and ide-h8300
(h8300 arch specific).
* Add "probe_vlb" kernel parameter to cmd640 host driver and update
Documentation/ide.txt accordingly.
* Make IDE_ARM config option visible so it can also be disabled if needed.
* Remove bogus comment from ide.c while at it.
v2:
* Fix two issues spotted by Sergei:
- replace ENOMEM error value by ENOENT in ide-h8300 host driver
- fix MODULE_PARM_DESC() in cmd640 host driver
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Rename init_hwif_data() to ide_init_port_data() and export it.
* For all users of ide_register_hw() with 'initializing' argument set
hwif->present and hwif->hold are always zero so convert these host
drivers to use ide_find_port()+ide_init_port_data()+ide_init_port_hw()
instead (also no need for init_hwif_default() call since the setup
done by it gets over-ridden by ide_init_port_hw() call).
* Drop 'initializing' argument from ide_register_hw().
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_init_port_hw() helper.
* rapide.c: convert rapide_locate_hwif() to rapide_setup_ports()
and use ide_init_port_hw().
* ide_platform.c: convert plat_ide_locate_hwif() to plat_ide_setup_ports()
and use ide_init_port_hw().
* sgiioc4.c: use ide_init_port_hw().
* pmac.c: add 'hw_regs_t *hw' argument to pmac_ide_setup_device(),
setup 'hw' in pmac_ide_{macio,pci}_attach() and use ide_init_port_hw()
in pmac_ide_setup_device().
This patch is a preparation for the future changes in the IDE probing code.
There should be no functionality changes caused by this patch.
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Jeremy Higdon <jeremy@sgi.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix build break of powerpc holly_defconfig:
In file included from arch/powerpc/platforms/embedded6xx/holly.c:24:
include/linux/ide.h:1206: error: 'CONFIG_IDE_MAX_HWIFS' undeclared here (not in a function)
There's no need to have a sized array in the prototype, might as well
turn it into a pointer.
It could probably be argued that large parts of the include file can be
covered under #ifdef CONFIG_IDE, but that's a larger undertaking.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Rename ide_device_add() to ide_device_add_all() and make it accept
'u8 idx[MAX_HWIFS]' instead of 'u8 idx[4]' as an argument.
* Add ide_device_add() wrapper for ide_device_add_all().
* Convert ide_generic_init() to use ide_device_add_all().
* Remove no longer needed ideprobe_init().
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Assign drive->quirk_list in ->quirkproc implementations:
- hpt366.c::hpt3xx_quirkproc()
- pdc202xx_new.c::pdcnew_quirkproc()
- pdc202xx_old.c::pdc202xx_quirkproc()
* Make ->quirkproc void.
* Move calling ->quirkproc from do_identify() to probe_hwif().
* Convert it821x_fixups() to it821x_quirkproc() in it821x.c.
* Convert siimage_fixup() to sil_quirkproc() in siimage.c, also remove
no longer needed drive->present check from is_dev_seagate_sata().
* Convert ide_undecoded_slave() to accept 'drive' instead of 'hwif'
as an argument. Then convert ide_register_hw() to accept 'quirkproc'
argument instead of 'fixup' one.
* Remove no longer needed ->fixup method.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Merge ->dma_host_{on,off} methods into ->dma_host_set method
which takes 'int on' argument.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Patrick McHardy