[ Upstream commit da09daf881082266e4075657fac53c7966de8e4d ]
There are two events that signal a real change of the link state: HPD going
high means the sink is newly connected or wants the source to re-read the
EDID, RX sense going low is a indication that the link has been disconnected.
Ignore the other two events that also trigger interrupts, but don't need
immediate attention: HPD going low does not necessarily mean the link has
been lost and should not trigger a immediate read of the status. RX sense
going high also does not require a detect cycle, as HPD going high is the
right point in time to read the EDID.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> (v1)
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220826185733.3213248-1-l.stach@pengutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef8886f321c5dab8124b9153d25afa2a71d05323 ]
A NULL check for bridge->encoder shows that it may be NULL, but it
already been dereferenced on all paths leading to the check.
812 if (!bridge->encoder) {
Dereference the pointer bridge->encoder.
810 drm_connector_attach_encoder(<9611->connector, bridge->encoder);
Signed-off-by: Zeng Jingxiang <linuszeng@tencent.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220727073119.1578972-1-zengjx95@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ff673333d46d2c1b053ebd0c1c7c7c79e36943e ]
When removing the module we will get the following warning:
[ 31.911505] i2c-core: driver [stdp2690-ge-b850v3-fw] unregistered
[ 31.912484] general protection fault, probably for non-canonical address 0xdffffc0000000001: 0000 [#1] PREEMPT SMP KASAN PTI
[ 31.913338] KASAN: null-ptr-deref in range [0x0000000000000008-0x000000000000000f]
[ 31.915280] RIP: 0010:drm_bridge_remove+0x97/0x130
[ 31.921825] Call Trace:
[ 31.922533] stdp4028_ge_b850v3_fw_remove+0x34/0x60 [megachips_stdpxxxx_ge_b850v3_fw]
[ 31.923139] i2c_device_remove+0x181/0x1f0
The two bridges (stdp2690, stdp4028) do not probe at the same time, so
the driver does not call ge_b850v3_resgiter() when probing, causing the
driver to try to remove the object that has not been initialized.
Fix this by checking whether both the bridges are probed.
Fixes: 11632d4aa2b3 ("drm/bridge: megachips: Ensure both bridges are probed before registration")
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220830073450.1897020-1-zheyuma97@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc94224c2e0ae8d83ac511a3ef4962178505469d ]
The datasheet says that VDD12 must be enabled and at full voltage before
VDD33 is enabled.
Reorder the bulk regulator supply names so that VDD12 is enabled before
VDD33. Any enable ramp delays should be handled by setting proper
constraints on the regulators.
Fixes: bc1aee7fc8 ("drm/bridge: Add I2C based driver for ps8640 bridge")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220721092258.3397461-1-wenst@chromium.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1d22b6033ea113a4c3850dfa2c0770885c81aec8 ]
The ADV7511_REG_CEC_CTRL = 0xE2 register is part of the main register
map - not the CEC register map. As such, we shouldn't apply an offset to
the register address. Doing so will cause us to address a bogus register
for chips with a CEC register map offset (e.g. ADV7533).
Fixes: 3b1b975003 ("drm: adv7511/33: add HDMI CEC support")
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220612144854.2223873-2-alvin@pqrs.dk
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc62d98bd56d45de4531844ca23913a15136c05b ]
This reverts commit 211f276ed3.
For quite some time, core DRM helpers already ensure that any relevant
connectors/CRTCs/etc. are disabled, as well as their associated
components (e.g., bridges) when suspending the system. Thus,
analogix_dp_bridge_{enable,disable}() already get called, which in turn
call drm_panel_{prepare,unprepare}(). This makes these drm_panel_*()
calls redundant.
Besides redundancy, there are a few problems with this handling:
(1) drm_panel_{prepare,unprepare}() are *not* reference-counted APIs and
are not in general designed to be handled by multiple callers --
although some panel drivers have a coarse 'prepared' flag that mitigates
some damage, at least. So at a minimum this is redundant and confusing,
but in some cases, this could be actively harmful.
(2) The error-handling is a bit non-standard. We ignored errors in
suspend(), but handled errors in resume(). And recently, people noticed
that the clk handling is unbalanced in error paths, and getting *that*
right is not actually trivial, given the current way errors are mostly
ignored.
(3) In the particular way analogix_dp_{suspend,resume}() get used (e.g.,
in rockchip_dp_*(), as a late/early callback), we don't necessarily have
a proper PM relationship between the DP/bridge device and the panel
device. So while the DP bridge gets resumed, the panel's parent device
(e.g., platform_device) may still be suspended, and so any prepare()
calls may fail.
So remove the superfluous, possibly-harmful suspend()/resume() handling
of panel state.
Fixes: 211f276ed3 ("drm: bridge: analogix/dp: add panel prepare/unprepare in suspend/resume time")
Link: https://lore.kernel.org/all/Yv2CPBD3Picg%2FgVe@google.com/
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220822180729.1.I8ac5abe3a4c1c6fd5c061686c6e883c22f69022c@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9030a9e571b3ba250d3d450a98310e3c74ecaff4 upstream.
Per toshiba,tc358767.yaml DT binding document, port@2 the output (e)DP
port is optional. In case this port is not described in DT, the bridge
driver operates in DPI-to-DP mode. The drm_of_find_panel_or_bridge()
call in tc_probe_edp_bridge_endpoint() returns -ENODEV in case port@2
is not present in DT and this specific return value is incorrectly
propagated outside of tc_probe_edp_bridge_endpoint() function. All
other error values must be propagated and are propagated correctly.
Return 0 in case the port@2 is missing instead, that reinstates the
original behavior before the commit this patch fixes.
Fixes: 8478095a8c4b ("drm/bridge: tc358767: Move (e)DP bridge endpoint parsing into dedicated function")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220428213132.447890-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 21779cc21c732c5eff8ea1624be6590450baa30f ]
The next call to sii8620_burst_get_tx_buf will result in off-by-one
When ctx->burst.tx_count + size == ARRAY_SIZE(ctx->burst.tx_buf). The same
thing happens in sii8620_burst_get_rx_buf.
This patch also change tx_count and tx_buf to rx_count and rx_buf in
sii8620_burst_get_rx_buf. It is unreasonable to check tx_buf's size and
use rx_buf.
Fixes: e19e9c692f ("drm/bridge/sii8620: add support for burst eMSC transmissions")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220518065856.18936-1-hbh25y@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 831463667b5f4f1e5bce9c3b94e9e794d2bc8923 ]
As mipi_dsi_driver_register could return error if fails,
it should be better to check the return value and return error
if fails.
Moreover, if i2c_add_driver fails, mipi_dsi_driver_register
should be reverted.
Fixes: 1e4d58cd7f ("drm/bridge: adv7533: Create a MIPI DSI device")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220602103401.2980938-1-jiasheng@iscas.ac.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9cc4853e4781bf0dd0f35355dc92d97c9da02f5d ]
Commit 680532c50b ("drm: adv7511: Add support for
i2c_new_secondary_device") allows a device tree node to override
the default addresses of the secondary i2c devices. This is useful
for solving address conflicts on the i2c bus.
In adv7511_init_cec_regmap() the new i2c address of cec device is
read from device tree and immediately accessed, well before it is
written in the proper register to override the default address.
This can cause an i2c error during probe and a consequent probe
failure.
Once the new i2c address is read from the device tree, override
the default address before any attempt to access the cec.
Tested with adv7533 and stm32mp157f.
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Fixes: 680532c50b ("drm: adv7511: Add support for i2c_new_secondary_device")
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220607213144.427177-1-antonio.borneo@foss.st.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b4c48f3e315d172e4cc06e10f2c8ba180788baf ]
The Refclk may be supplied by SoC clock output instead of crystal
oscillator, make sure the clock are enabled before any other action
is performed with the bridge chip, otherwise it may either fail to
operate at all, or miss reset GPIO toggle.
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Fixes: 7caff0fc42 ("drm/bridge: tc358767: Add DPI to eDP bridge driver")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220520121543.11550-1-marex@denx.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8478095a8c4bcea3c83b0767d6c9127434160761 ]
The TC358767/TC358867/TC9595 are all capable of operating in multiple
modes, DPI-to-(e)DP, DSI-to-(e)DP, DSI-to-DPI. Only the first mode is
currently supported. In order to support the rest of the modes without
making the tc_probe() overly long, split the bridge endpoint parsing
into dedicated function, where the necessary logic to detect the bridge
mode based on which endpoints are connected, can be implemented.
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Lucas Stach <l.stach@pengutronix.de> # In both DPI to eDP and DSI to DPI mode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220329085015.39159-7-marex@denx.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ca871659ec1606d33b1e76de8d4cf924cf627e34 upstream.
Most eDP panel functions only work correctly when the panel is not in
self-refresh. In particular, analogix_dp_bridge_disable() tends to hit
AUX channel errors if the panel is in self-refresh.
Given the above, it appears that so far, this driver assumes that we are
never in self-refresh when it comes time to fully disable the bridge.
Prior to commit 846c7dfc11 ("drm/atomic: Try to preserve the crtc
enabled state in drm_atomic_remove_fb, v2."), this tended to be true,
because we would automatically disable the pipe when framebuffers were
removed, and so we'd typically disable the bridge shortly after the last
display activity.
However, that is not guaranteed: an idle (self-refresh) display pipe may
be disabled, e.g., when switching CRTCs. We need to exit PSR first.
Stable notes: this is definitely a bugfix, and the bug has likely
existed in some form for quite a while. It may predate the "PSR helpers"
refactor, but the code looked very different before that, and it's
probably not worth rewriting the fix.
Cc: <stable@vger.kernel.org>
Fixes: 6c836d965b ("drm/rockchip: Use the helpers for PSR")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220228122522.v2.1.I161904be17ba14526f78536ccd78b85818449b51@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8fb6c44fe8468f92ac7b8bbfcca4404a4e88645f upstream.
If the display is not enable()d, then we aren't holding a runtime PM
reference here. Thus, it's easy to accidentally cause a hang, if user
space is poking around at /dev/drm_dp_aux0 at the "wrong" time.
Let's get a runtime PM reference, and check that we "see" the panel.
Don't force any panel power-up, etc., because that can be intrusive, and
that's not what other drivers do (see
drivers/gpu/drm/bridge/ti-sn65dsi86.c and
drivers/gpu/drm/bridge/parade-ps8640.c.)
Fixes: 0d97ad03f4 ("drm/bridge: analogix_dp: Remove duplicated code")
Cc: <stable@vger.kernel.org>
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220301181107.v4.1.I773a08785666ebb236917b0c8e6c05e3de471e75@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9f15930bb2ef9f031d62ffc49629cbae89137733 ]
In the error handling path, the clk_prepare_enable() function
call should be balanced by a corresponding 'clk_disable_unprepare()'
call, as already done in the remove function.
Fixes: 3424e3a4f8 ("drm: bridge: analogix/dp: split exynos dp driver to bridge directory")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220420011644.25730-1-linmq006@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ed2b0dabf7a22874cb30f8878df239ef638eb53 ]
When the probe routine fails we also need to clean up the
CEC adapter registered in adv7511_cec_init().
Fixes: 3b1b975003 ("drm: adv7511/33: add HDMI CEC support")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220321104705.2804423-1-l.stach@pengutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ffb5c099aaa13ab7f73c29ea6ae26bce8d7575ae ]
Add MODULE_DEVICE_TABLE to the device tree table to create required
aliases needed for module to be loaded with device tree based platform.
Fixes: e19233955d ("drm/bridge: Add Cadence DSI driver")
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921174059.17946-1-nm@ti.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1528038385c0a706aac9ac165eeb24044fef6825 ]
When the dw-hdmi bridge is in first place of the bridge chain, this
means there is no way to select an input format of the dw-hdmi HW
component.
Since introduction of display-connector, negotiation was broken since
the dw-hdmi negotiation code only worked when the dw-hdmi bridge was
in last position of the bridge chain or behind another bridge also
supporting input & output format negotiation.
Commit 7cd70656d128 ("drm/bridge: display-connector: implement bus fmts callbacks")
was introduced to make negotiation work again by making display-connector
act as a pass-through concerning input & output format negotiation.
But in the case where the dw-hdmi is single in the bridge chain, for
example on Renesas SoCs, with the display-connector bridge the dw-hdmi
is no more single, breaking output format.
Reported-by: Biju Das <biju.das.jz@bp.renesas.com>
Bisected-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Tested-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Fixes: 6c3c719936 ("drm/bridge: synopsys: dw-hdmi: add bus format negociation")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: add proper fixes commit]
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220204143337.89221-1-narmstrong@baylibre.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3dbc84a595d17f64f14fcea00120d31e33e98880 ]
Existing HPD enablement logic is not compatible with ADV7535
bridge, thus any runtime plug-in of HDMI cable is not working
on these bridge designs.
Unlike other ADV7511 family of bridges, the ADV7535 require
HPD_OVERRIDE bit to set and reset for proper handling of HPD
functionality.
Fix it.
Fixes: 8501fe4b14 ("drm: bridge: adv7511: Add support for ADV7535")
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220109172949.168167-1-jagan@amarulasolutions.com
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b146e343a9e05605b491b1bf4a2b62a39d5638d8 ]
The pm_runtime_enable will increase power disable depth.
Thus a pairing decrement is needed on the error handling
path to keep it balanced according to context.
Fixes: 44cfc62334 ("drm/bridge: Add NWL MIPI DSI host controller support")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220105104826.1418-1-linmq006@gmail.com
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 96211b7c56b109a52768e6cc5e23a1f79316eca0 ]
If the probe fails, we should use pm_runtime_disable() to balance
pm_runtime_enable().
Add missing pm_runtime_disable() for __dw_mipi_dsi_probe.
Fixes: 46fc51546d ("drm/bridge/synopsys: Add MIPI DSI host controller bridge")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220105104113.31415-1-linmq006@gmail.com
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c442e76c06cb1bef16a6c523487438175584eea ]
rc_dev is allocated by rc_allocate_device(), and doesn't assigned to
ctx->rc_dev before calling rc_free_device(ctx->rc_dev).
So it should call rc_free_device(rc_dev);
Fixes: e25f1f7c94 ("drm/bridge/sii8620: add remote control support")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211227092522.21755-1-linmq006@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c4c6ef229593366ab593d4d424addc7025b54a76 upstream.
Prior to commit 6c836d965b ("drm/rockchip: Use the helpers for PSR"),
"PSR exit" used non-blocking analogix_dp_send_psr_spd(). The refactor
started using the blocking variant, for a variety of reasons -- quoting
Sean Paul's potentially-faulty memory:
"""
- To avoid racing a subsequent PSR entry (if exit takes a long time)
- To avoid racing disable/modeset
- We're not displaying new content while exiting PSR anyways, so there
is minimal utility in allowing frames to be submitted
- We're lying to userspace telling them frames are on the screen when
we're just dropping them on the floor
"""
However, I'm finding that this blocking transition is causing upwards of
60+ ms of unneeded latency on PSR-exit, to the point that initial cursor
movements when leaving PSR are unbearably jumpy.
It turns out that we need to meet in the middle somewhere: Sean is right
that we were "lying to userspace" with a non-blocking PSR-exit, but the
new blocking behavior is also waiting too long:
According to the eDP specification, the sink device must support PSR
entry transitions from both state 4 (ACTIVE_RESYNC) and state 0
(INACTIVE). It also states that in ACTIVE_RESYNC, "the Sink device must
display the incoming active frames from the Source device with no
visible glitches and/or artifacts."
Thus, for our purposes, we only need to wait for ACTIVE_RESYNC before
moving on; we are ready to display video, and subsequent PSR-entry is
safe.
Tested on a Samsung Chromebook Plus (i.e., Rockchip RK3399 Gru Kevin),
where this saves about 60ms of latency, for PSR-exit that used to
take about 80ms.
Fixes: 6c836d965b ("drm/rockchip: Use the helpers for PSR")
Cc: <stable@vger.kernel.org>
Cc: Zain Wang <wzz@rock-chips.com>
Cc: Tomasz Figa <tfiga@chromium.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211103135112.v3.1.I67612ea073c3306c71b46a87be894f79707082df@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3f2532d65a571ca02258b547b5b68ab2e9406fdb ]
The current ELD handling takes the internal connector ELD buffer and
shares it to the I2S and AHB sub-driver.
But with DRM_BRIDGE_ATTACH_NO_CONNECTOR, the connector is created
elsewhere (or not), and an eventual connector is known only
if the bridge chain up to a connector is enabled.
The current dw-hdmi code gets the current connector from
atomic_enable() so use the already stored connector pointer and
replace the buffer pointer with a callback returning the current
connector ELD buffer.
Since a connector is not always available, either pass an empty
ELD to the alsa HDMI driver or don't call snd_pcm_hw_constraint_eld()
in AHB driver.
Reported-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: fixed typo in commit log]
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211029135947.3022875-1-narmstrong@baylibre.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b665d4af35837f0a0ae63135b84a3c187c1db3b ]
Set the maximum register to 0xff so we can dump the registers for this
device in debugfs.
Fixes: a095f15c00 ("drm/bridge: add support for sn65dsi86 bridge driver")
Cc: Rob Clark <robdclark@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211215002529.382383-1-swboyd@chromium.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 189723fbe9aca18d6f7d638c59a40288030932b5 ]
The "label" pointer is used for debug output. The code assumes that it
is either NULL or valid, but it is never set to NULL. It is either
valid or uninitialized.
Fixes: 0c275c3017 ("drm/bridge: Add bridge driver for display connectors")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211013080825.GE6010@kili
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d1a97648ae028a44536927c87837c45ada7141c9 upstream.
4k requires two dsi pipes, so don't report MODE_OK when only a
single pipe is configured. But rather report MODE_PANEL to
signal that requirements of the panel are not being met.
Reported-by: Peter Collingbourne <pcc@google.com>
Suggested-by: Peter Collingbourne <pcc@google.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Tested-by: Anibal Limon <anibal.limon@linaro.org>
Tested-by: Peter Collingbourne <pcc@google.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201217140933.1133969-1-robert.foss@linaro.org
Cc: Peter Collingbourne <pcc@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 47956bc86ee4e8530cac386a04f62a6095f7afbe ]
As nwl_dsi.lanes is u32, and NSEC_PER_SEC is 1000000000L, the second
multiplication in
dsi->lanes * 8 * NSEC_PER_SEC
will overflow on a 32-bit platform. Fix this by making the constant
unsigned long long, forcing 64-bit arithmetic.
As iMX8 is arm64, this driver is currently used on 64-bit platforms
only, where long is 64-bit, so this cannot happen. But the issue will
start to happen when the driver is reused for a 32-bit SoC (e.g.
i.MX7ULP), or when code is copied for a new driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/ebb82941a86b4e35c4fcfb1ef5a5cfad7c1fceab.1626255956.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f674555ee5444c8987dfea0922f1cf6bf0c12847 ]
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210531135622.3348252-1-yukuai3@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 33f90f27e1c5ccd648d3e78a1c28be9ee8791cf1 ]
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1621840862-106024-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d0b1fe81e18eb66a2d4406386760795fe0d77d9 ]
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1620801955-19188-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3afb2a28fa2404d11cce1956a003f2aaca4da421 ]
This patch replaces ->mode_fixup() with ->atomic_check() so that
a full modeset can be requested from there when crtc_state->active
is changed to be true(which implies only connector's DPMS is brought
out of "Off" status, though not necessarily). Bridge functions are
added or changed to accommodate the ->atomic_check() callback. That
full modeset is needed by the up-coming patch which gets MIPI DSI
controller and PHY ready in ->mode_set(), because it makes sure
->mode_set() and ->atomic_disable() are called in pairs.
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Guido Günther <agx@sigxcpu.org>
Cc: Robert Chiras <robert.chiras@nxp.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1619170003-4817-2-git-send-email-victor.liu@nxp.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08319adbdde15ef7cee1970336f63461254baa2a ]
The DRM_SIL_SII8620 kconfig has a weak `imply` dependency
on EXTCON, which causes issues when sii8620 is built
as a builtin and EXTCON is built as a module.
The symptoms are 'undefined reference' errors caused
by the symbols in EXTCON not being available
to the sii8620 driver.
Fixes: 6888384421 ("drm/bridge/sii8620: use micro-USB cable detection logic to detect MHL")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210419090124.153560-1-robert.foss@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4d906839d321c2efbf3fed4bc31ffd9ff55b75c0 upstream.
If we don't call drm_connector_cleanup() manually in
panel_bridge_detach(), the connector will be cleaned up with the other
DRM objects in the call to drm_mode_config_cleanup(). However, since our
drm_connector is devm-allocated, by the time drm_mode_config_cleanup()
will be called, our connector will be long gone. Therefore, the
connector must be cleaned up when the bridge is detached to avoid
use-after-free conditions.
v2: Cleanup connector only if it was created
v3: Add FIXME
v4: (Use connector->dev) directly in if() block
Fixes: 13dfc0540a ("drm/bridge: Refactor out the panel wrapper from the lvds-encoder bridge.")
Cc: <stable@vger.kernel.org> # 4.12+
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210327115742.18986-2-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc5f7e2fcbe396f2f461cd67c872af771a334bca upstream.
On the SII9022, the IOVCC and CVCC12 supplies must reach the correct
voltage before the reset sequence is initiated. On most boards, this
assumption is true at boot-up, so initialization succeeds.
However, when we try to initialize the chip with incorrect supply
voltages, it will not respond to I2C requests. sii902x_probe() fails
with -ENXIO.
To resolve this, look for the "iovcc" and "cvcc12" regulators, and
make sure they are enabled before starting the reset sequence. If
these supplies are not available in devicetree, then they will default
to dummy-regulator. In that case everything will work like before.
This was observed on a STM32MP157C-DK2 booting in u-boot falcon mode.
On this board, the supplies would be set by the second stage
bootloader, which does not run in falcon mode.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
[Fix checkpatch warnings]
Link: https://patchwork.freedesktop.org/patch/msgid/20201020221501.260025-2-mr.nuke.me@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 91b5e26731c5d409d6134603afc061617639933e upstream.
Separate the hardware initialization code from setting up the data
structures and parsing the device tree. The purpose of this change is
to provide a single exit point and avoid a waterfall of 'goto's in
the subsequent patch.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201020221501.260025-1-mr.nuke.me@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c2530cc9610d84a5a0118ba40d0f09309605047f ]
gpiod_to_irq() return negative value in case of error,
the existing code doesn't handle negative error codes.
If the HPD gpio supports IRQs (gpiod_to_irq returns a
valid number), we use the IRQ. If it doesn't (gpiod_to_irq
returns an error), it gets polled via detect().
Fixes: cff5e6f7e8 ("drm/bridge: Add driver for the TI TPD12S015 HDMI level shifter")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201102143024.26216-1-yuehaibing@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
It has been observed that resetting force in the detect function can
result in the PHY being powered down in response to hot-plug detect
being asserted, even when the HDMI connector is forced on.
Enabling debug messages and adding a call to dump_stack() in
dw_hdmi_phy_power_off() shows the following in dmesg:
[ 160.637413] dwhdmi-rockchip ff940000.hdmi: EVENT=plugin
[ 160.637433] dwhdmi-rockchip ff940000.hdmi: PHY powered down in 0 iterations
Call trace:
dw_hdmi_phy_power_off
dw_hdmi_phy_disable
dw_hdmi_update_power
dw_hdmi_detect
dw_hdmi_connector_detect
drm_helper_probe_detect_ctx
drm_helper_hpd_irq_event
dw_hdmi_irq
irq_thread_fn
irq_thread
kthread
ret_from_fork
Fixes: 381f05a7a8 ("drm: bridge/dw_hdmi: add connector mode forcing")
Signed-off-by: Jonathan Liu <net147@gmail.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201031081747.372599-1-net147@gmail.com
With the integration of chip-id detection scheme in kernel[1], there
is no specific need to maintain multitudes of SoC specific config
options, discussed as per [2], we have deprecated the usage in other
places for v5.10-rc1. Fix the missing user so that we can clean up the
configs in v5.11.
[1] drivers/soc/ti/k3-socinfo.c commit 907a2b7e2f ("soc: ti: add k3 platforms chipid module driver")
[2] https://lore.kernel.org/linux-arm-kernel/20200908112534.t5bgrjf7y3a6l2ss@akan/
Fixes: afba7e6c5f ("drm: bridge: cdns-mhdp8546: Add TI J721E wrapper")
Cc: Swapnil Jakhade <sjakhade@cadence.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Yuti Amonkar <yamonkar@cadence.com>
Cc: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201026165441.22894-1-nm@ti.com
On x64 we get:
drivers/gpu/drm/bridge/cadence/cdns-mhdp8546-core.c:751:10: warning: conversion from 'long unsigned int' to 'unsigned int' changes value from '18446744073709551613' to '4294967293' [-Woverflow]
The registers are 32 bit, so fix by casting to u32.
Fixes: fb43aa0acd ("drm: bridge: Add support for Cadence MHDP8546 DPI/DP bridge")
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Swapnil Jakhade <sjakhade@cadence.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200929091918.24813-1-tomi.valkeinen@ti.com
UAPI Changes:
Cross-subsystem Changes:
Core Changes:
- dev: More devm_drm convertions and removal of drm_dev_init
Driver Changes:
- i915: selftests improvements
- panfrost: support for Amlogic SoC
- vc4: one fix
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCX2jGxQAKCRDj7w1vZxhR
xR3DAQCiZOnaxVcY49iG4343Z1aHHaIEShbnB0bDdaWstn7kiQD/UXBXUoOSFoFQ
FkTsW31JsdXNnWP5e6/eJd2Lb6waVAA=
=VlsU
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2020-09-21' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.10:
UAPI Changes:
Cross-subsystem Changes:
- virtio: Merged a PR for patches that will affect drm/virtio
Core Changes:
- dev: More devm_drm convertions and removal of drm_dev_init
- atomic: Split out drm_atomic_helper_calc_timestamping_constants of
drm_atomic_helper_update_legacy_modeset_state
- ttm: More rework
Driver Changes:
- i915: selftests improvements
- panfrost: support for Amlogic SoC
- vc4: one fix
- tree-wide: conversions to devm_drm_dev_alloc,
- ast: simplifications of the atomic modesetting code
- panfrost: multiple fixes
- vc4: multiple fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20200921152956.2gxnsdgxmwhvjyut@gilmour.lan
Add the support for enabling optional regulator that may be used as VCC
source.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[Replaced 'error' variable with 'ret']
[Renamed regulator from 'vcc' to 'power']
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Add J721E wrapper for mhdp, which sets up the clock and data muxes.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Yuti Amonkar <yamonkar@cadence.com>
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add a new DRM bridge driver for Cadence MHDP8546 DPTX IP used in TI J721E
SoC. MHDP DPTX IP is the component that complies with VESA DisplayPort (DP)
and embedded Display Port (eDP) standards. It integrates uCPU running the
embedded Firmware (FW) interfaced over APB interface.
Basically, it takes a DPI stream as input and outputs it encoded in DP
format. Currently, it supports only SST mode.
Co-developed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Co-developed-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Yuti Amonkar <yamonkar@cadence.com>
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The get_edid() callback can be triggered anytime by an ioctl, i.e
drm_mode_getconnector (ioctl)
-> drm_helper_probe_single_connector_modes
-> drm_bridge_connector_get_modes
-> ps8640_bridge_get_edid
Actually if the bridge pre_enable() function was not called before
get_edid(), the driver will not be able to get the EDID properly and
display will not work until a second get_edid() call is issued and if
pre_enable() is called before. The side effect of this, for example, is
that you see anything when `Frecon` starts, neither the splash screen,
until the graphical session manager starts.
To fix this we need to make sure that all we need is enabled before
reading the EDID. This means the following:
1. If get_edid() is called before having the device powered we need to
power on the device. In such case, the driver will power off again the
device.
2. If get_edid() is called after having the device powered, all should
just work. We added a powered flag in order to avoid recurrent calls
to ps8640_bridge_poweron() and unneeded delays.
3. This seems to be specific for this device, but we need to make sure
the panel is powered on before do a power on cycle on this device.
Otherwise the device fails to retrieve the EDID.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Bilal Wasim <bwasim.lkml@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200827085911.944899-2-enric.balletbo@collabora.com
Lucas Stach