The NIC has a limited number of offloaded VXLAN UDP ports (usually 4).
Instead of letting the firmware fail when trying to add more ports than
it can handle, let the driver check it on its own.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
mlx5 core infrastructure updates and fixes.
From Eran:
- Add MPEGC (Management PCIe General Configuration) registers and btis
- Fix tristate and description for MLX5 module
rom Feras:
- Add hardware structures for the firmware tracer
From Jainbo:
- Core support for double vlan push/pop steering action
From Max:
- Add XRQ commands definitions
From Noa:
- Add missing SET_DRIVER_VERSION command translation
From Roi:
- Use ERR_CAST() instead of coding it
From Tariq:
- Better return types for CQE API
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
As newer firmware supports double push/pop in a single FTE, we add
core bits and extend vlan action logic for it.
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This patch exposes PRM layout for handling MPEGC (Management PCIe
General Configuration).
This will be used in the downstream patch for configuring MPEGC via the
driver.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This change adds the infrastructure to mlx5 core fw tracer.
It introduces the following 4 new registers:
MLX5_REG_MTRC_CAP - Used to read tracer capabilities
MLX5_REG_MTRC_CONF - Used to set tracer configurations
MLX5_REG_MTRC_STDB - Used to query tracer strings database
MLX5_REG_MTRC_CTRL - Used to control the tracer
The capability of the tracing can be checked using mcam access
register, therefore, the mcam access register interface will expose
the tracer register.
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
MLX5 IB HCA offers the memory key, dump_fill_mkey to boost
performance by forcing local HCA operations to skip the PCI bus
access,
This patch adds needed hardware definitions.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
In smartnic env, the host (PF) driver might not be an e-switch
manager, hence the FW will err on driver attempts to deal with
setting/unsetting the eswitch and as a result the overall setup
of sriov will fail.
Fix that by avoiding the operation if e-switch management is not
allowed for this driver instance. While here, move to use the
correct name for the esw manager capability name.
Fixes: 81848731ff ('net/mlx5: E-Switch, Add SR-IOV (FDB) support')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Guy Kushnir <guyk@mellanox.com>
Reviewed-by: Eli Cohen <eli@melloanox.com>
Tested-by: Eli Cohen <eli@melloanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add capability bit in PCAM register and RoCE ICRC error counter
to PPCNT register.
Signed-off-by: Talat Batheesh <talatb@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
This patch updates the mlx5_ifc structures and
command interface to support DEVX.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
This has been a quiet cycle for RDMA, the big bulk is the usual smallish
driver updates and bug fixes. About four new uAPI related things. Not as much
Szykaller patches this time, the bugs it finds are getting harder to fix.
- More work cleaning up the RDMA CM code
- Usual driver bug fixes and cleanups for qedr, qib, hfi1, hns, i40iw, iw_cxgb4, mlx5, rxe
- Driver specific resource tracking and reporting via netlink
- Continued work for name space support from Parav
- MPLS support for the verbs flow steering uAPI
- A few tricky IPoIB fixes improving robustness
- HFI1 driver support for the '16B' management packet format
- Some auditing to not print kernel pointers via %llx or similar
- Mark the entire 'UCM' user-space interface as BROKEN with the intent to remove it
entirely. The user space side of this was long ago replaced with RDMA-CM and
syzkaller is finding bugs in the residual UCM interface nobody wishes to fix because
nobody uses it.
- Purge more bogus BUG_ON's from Leon
- 'flow counters' verbs uAPI
- T10 fixups for iser/isert, these are Acked by Martin but going through the RDMA
tree due to dependencies
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Mb8m
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"This has been a quiet cycle for RDMA, the big bulk is the usual
smallish driver updates and bug fixes. About four new uAPI related
things. Not as much Szykaller patches this time, the bugs it finds are
getting harder to fix.
Summary:
- More work cleaning up the RDMA CM code
- Usual driver bug fixes and cleanups for qedr, qib, hfi1, hns,
i40iw, iw_cxgb4, mlx5, rxe
- Driver specific resource tracking and reporting via netlink
- Continued work for name space support from Parav
- MPLS support for the verbs flow steering uAPI
- A few tricky IPoIB fixes improving robustness
- HFI1 driver support for the '16B' management packet format
- Some auditing to not print kernel pointers via %llx or similar
- Mark the entire 'UCM' user-space interface as BROKEN with the
intent to remove it entirely. The user space side of this was long
ago replaced with RDMA-CM and syzkaller is finding bugs in the
residual UCM interface nobody wishes to fix because nobody uses it.
- Purge more bogus BUG_ON's from Leon
- 'flow counters' verbs uAPI
- T10 fixups for iser/isert, these are Acked by Martin but going
through the RDMA tree due to dependencies"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (138 commits)
RDMA/mlx5: Update SPDX tags to show proper license
RDMA/restrack: Change SPDX tag to properly reflect license
IB/hfi1: Fix comment on default hdr entry size
IB/hfi1: Rename exp_lock to exp_mutex
IB/hfi1: Add bypass register defines and replace blind constants
IB/hfi1: Remove unused variable
IB/hfi1: Ensure VL index is within bounds
IB/hfi1: Fix user context tail allocation for DMA_RTAIL
IB/hns: Use zeroing memory allocator instead of allocator/memset
infiniband: fix a possible use-after-free bug
iw_cxgb4: add INFINIBAND_ADDR_TRANS dependency
IB/isert: use T10-PI check mask definitions from core layer
IB/iser: use T10-PI check mask definitions from core layer
RDMA/core: introduce check masks for T10-PI offload
IB/isert: fix T10-pi check mask setting
IB/mlx5: Add counters read support
IB/mlx5: Add flow counters read support
IB/mlx5: Add flow counters binding support
IB/mlx5: Add counters create and destroy support
IB/uverbs: Add support for flow counters
...
The FPGA queue pair (QP) event fires whenever a QP on the FPGA
transitions to the error state.
At this stage, this event is unrecoverable, it may become recoverable
in the future.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Adi Nissim <adin@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Temperature warning event is sent by FW to indicate high temperature
as detected by one of the sensors on the board.
Add handling of this event by writing the numbers of the alert sensors
to the kernel log.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Adi Nissim <adin@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Leon Romanovsky says:
====================
Introduce new internal to mlx5 CQE format - mini-CQE. It is a CQE in
compressed form that holds data needed to extra a single full CQE.
It is a stride index, byte count and packet checksum.
====================
* mini_cqe:
IB/mlx5: Introduce a new mini-CQE format
IB/mlx5: Refactor CQE compression response
net/mlx5: Exposing a new mini-CQE format
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The new mini-CQE format includes byte-count, checksum
and stride index.
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Guy Levi <guyle@mellanox.com>
Signed-off-by: Yonatan Cohen <yonatanc@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
If set, the FDB table supports the forward action with a
destination list that includes a flow table.
Signed-off-by: Chris Mi <chrism@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add pbmc and pptb in the port_access_reg_cap_mask. These two
bits determine if device supports receive buffer configuration.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
mlx5 core dirver updates for both net-next and rdma-next branches.
From Christophe JAILLET, first three patche to use kvfree where needed.
From: Or Gerlitz <ogerlitz@mellanox.com>
Next six patches from Roi and Co adds support for merged
sriov e-switch which comes to serve cases where both PFs, VFs set
on them and both uplinks are to be used in single v-switch SW model.
When merged e-switch is supported, the per-port e-switch is logically
merged into one e-switch that spans both physical ports and all the VFs.
This model allows to offload TC eswitch rules between VFs belonging
to different PFs (and hence have different eswitch affinity), it also
sets the some of the foundations needed for uplink LAG support.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJa/fLEAAoJEEg/ir3gV/o+7jUH/3n5/Uw1LLt3TfeKArx6i0F1
3G4U5B0ha03qiDqXprwhyQ3I6lgYmRBmjcxnqmvcqOAqO4/hSsjtTR+A/mgbEDhJ
YtdekFNEX+72h/N2GIpZwChIWSE3EcMPaLYnV8TwLUgh9YSust2sCLSBbJCjxOKc
j78M8ept/bXZwTm/iJhEjtmqw0xl91rl011chCAua0iEpH3wxteDARmKABFHMQxl
I3N/x/e/astgcSCNgpO4uDf9zEIRkNdzcHPzSMJ6C2Oo5W9XiZEekfw7WKj9nXfa
G+eGckkAyCOQ/r2lZ9nA0ZUvQ2X6JISvxgohuaCNwTgsz3acTxbLnQK4YWHzQCQ=
=iHi6
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2018-05-17' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux into for-next
mlx5-updates-2018-05-17
mlx5 core dirver updates for both net-next and rdma-next branches.
From Christophe JAILLET, first three patche to use kvfree where needed.
From: Or Gerlitz <ogerlitz@mellanox.com>
Next six patches from Roi and Co adds support for merged
sriov e-switch which comes to serve cases where both PFs, VFs set
on them and both uplinks are to be used in single v-switch SW model.
When merged e-switch is supported, the per-port e-switch is logically
merged into one e-switch that spans both physical ports and all the VFs.
This model allows to offload TC eswitch rules between VFs belonging
to different PFs (and hence have different eswitch affinity), it also
sets the some of the foundations needed for uplink LAG support.
* tag 'mlx5-updates-2018-05-17' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
net/mlx5e: Explicitly set source e-switch in offloaded TC rules
net/mlx5: Add source e-switch owner
net/mlx5e: Explicitly set destination e-switch in FDB rules
net/mlx5: Add destination e-switch owner
net/mlx5: Properly handle a vport destination when setting FTE
net/mlx5: Add merged e-switch cap
IB/mlx5: Use 'kvfree()' for memory allocated by 'kvzalloc()'
net/mlx5: Eswitch, Use 'kvfree()' for memory allocated by 'kvzalloc()'
net/mlx5: Vport, Use 'kvfree()' for memory allocated by 'kvzalloc()'
mlx5 core dirver updates for both net-next and rdma-next branches.
From Christophe JAILLET, first three patche to use kvfree where needed.
From: Or Gerlitz <ogerlitz@mellanox.com>
Next six patches from Roi and Co adds support for merged
sriov e-switch which comes to serve cases where both PFs, VFs set
on them and both uplinks are to be used in single v-switch SW model.
When merged e-switch is supported, the per-port e-switch is logically
merged into one e-switch that spans both physical ports and all the VFs.
This model allows to offload TC eswitch rules between VFs belonging
to different PFs (and hence have different eswitch affinity), it also
sets the some of the foundations needed for uplink LAG support.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJa/fLEAAoJEEg/ir3gV/o+7jUH/3n5/Uw1LLt3TfeKArx6i0F1
3G4U5B0ha03qiDqXprwhyQ3I6lgYmRBmjcxnqmvcqOAqO4/hSsjtTR+A/mgbEDhJ
YtdekFNEX+72h/N2GIpZwChIWSE3EcMPaLYnV8TwLUgh9YSust2sCLSBbJCjxOKc
j78M8ept/bXZwTm/iJhEjtmqw0xl91rl011chCAua0iEpH3wxteDARmKABFHMQxl
I3N/x/e/astgcSCNgpO4uDf9zEIRkNdzcHPzSMJ6C2Oo5W9XiZEekfw7WKj9nXfa
G+eGckkAyCOQ/r2lZ9nA0ZUvQ2X6JISvxgohuaCNwTgsz3acTxbLnQK4YWHzQCQ=
=iHi6
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2018-05-17' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Saeed Mahameed says:
====================
mlx5-updates-2018-05-17
mlx5 core dirver updates for both net-next and rdma-next branches.
From Christophe JAILLET, first three patche to use kvfree where needed.
From: Or Gerlitz <ogerlitz@mellanox.com>
Next six patches from Roi and Co adds support for merged
sriov e-switch which comes to serve cases where both PFs, VFs set
on them and both uplinks are to be used in single v-switch SW model.
When merged e-switch is supported, the per-port e-switch is logically
merged into one e-switch that spans both physical ports and all the VFs.
This model allows to offload TC eswitch rules between VFs belonging
to different PFs (and hence have different eswitch affinity), it also
sets the some of the foundations needed for uplink LAG support.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The source e-switch owner allows a vport on one e-switch port be associated
with a rule defined on the second port e-switch.
The role of the source eswitch owner valid bit in the flow group is to
allow the firmware fail driver attempts to wild card the source eswitch
match field. If this bit is not set, the firmware ignores the source
eswitch owner field totally.
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The destination e-switch owner allows a rule in namespace of one e-switch
owner to point to a vport that is natively associated with another
e-switch owner.
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When merged e-switch is supported, the per-port e-switch is logically
merged into one e-switch that spans both physical ports and all the VFs.
Under merged eswitch, both the matching on source vport and setting
destination vport can have a 2nd attribute which is the vhca id of the
eswitch owner.
For example:
esw0: {match: <src vport=1 owner=0> action: fwd to <dst vport=7, owner=1>}
is a flow set on eswitch0 matching on source vport=1 from his eswitch
and the action being fwd to dest vport=7 of eswitch1.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Shahar Klein <shahark@mellanox.com>
Reviewed-by: Or Gerlitz Klein <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This patch reports the device's capbilities to offload
encapsulated MPLS tunnel protocols to user-space:
- Capability to offload MPLS over GRE.
- Capability to offload MPLS over UDP.
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This patch introduces support for the MPLS flow spec and
allows the creation of rules that are matching on the
MPLS label.
Applying the rule matching depends on the flow specs order and
the location of the MPLS in the spec list as there are different
configurations to be made in the device in the cases of MPLSoGRE
and MPLSoUDP vs. non-encapsulated MPLS.
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Add routines for manipulating TLS TX offload contexts.
In Innova TLS, TLS contexts are added or deleted
via a command message over the SBU connection.
The HW then sends a response message over the same connection.
Add implementation for Innova TLS (FPGA-based) hardware.
These routines will be used by the TLS offload support in a later patch
mlx5/accel is a middle acceleration layer to allow mlx5e and other ULPs
to work directly with mlx5_core rather than Innova FPGA or other mlx5
acceleration providers.
In the future, when IPSec/TLS or any other acceleration gets integrated
into ConnectX chip, mlx5/accel layer will provide the integrated
acceleration, rather than the Innova one.
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix RDMA uapi headers to actually compile in userspace and be more
complete
- Three shared with netdev pull requests from Mellanox:
* 7 patches, mostly to net with 1 IB related one at the back). This
series addresses an IRQ performance issue (patch 1), cleanups related to
the fix for the IRQ performance problem (patches 2-6), and then extends
the fragmented completion queue support that already exists in the net
side of the driver to the ib side of the driver (patch 7).
* Mostly IB, with 5 patches to net that are needed to support the remaining
10 patches to the IB subsystem. This series extends the current
'representor' framework when the mlx5 driver is in switchdev mode from
being a netdev only construct to being a netdev/IB dev construct. The IB
dev is limited to raw Eth queue pairs only, but by having an IB dev of
this type attached to the representor for a switchdev port, it enables
DPDK to work on the switchdev device.
* All net related, but needed as infrastructure for the rdma driver
- Updates for the hns, i40iw, bnxt_re, cxgb3, cxgb4, hns drivers
- SRP performance updates
- IB uverbs write path cleanup patch series from Leon
- Add RDMA_CM support to ib_srpt. This is disabled by default. Users need to
set the port for ib_srpt to listen on in configfs in order for it to be
enabled (/sys/kernel/config/target/srpt/discovery_auth/rdma_cm_port)
- TSO and Scatter FCS support in mlx4
- Refactor of modify_qp routine to resolve problems seen while working on new
code that is forthcoming
- More refactoring and updates of RDMA CM for containers support from Parav
- mlx5 'fine grained packet pacing', 'ipsec offload' and 'device memory'
user API features
- Infrastructure updates for the new IOCTL interface, based on increased usage
- ABI compatibility bug fixes to fully support 32 bit userspace on 64 bit
kernel as was originally intended. See the commit messages for
extensive details
- Syzkaller bugs and code cleanups motivated by them
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Ku8g
-----END PGP SIGNATURE-----
Merge tag 'for-linus-unmerged' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"Doug and I are at a conference next week so if another PR is sent I
expect it to only be bug fixes. Parav noted yesterday that there are
some fringe case behavior changes in his work that he would like to
fix, and I see that Intel has a number of rc looking patches for HFI1
they posted yesterday.
Parav is again the biggest contributor by patch count with his ongoing
work to enable container support in the RDMA stack, followed by Leon
doing syzkaller inspired cleanups, though most of the actual fixing
went to RC.
There is one uncomfortable series here fixing the user ABI to actually
work as intended in 32 bit mode. There are lots of notes in the commit
messages, but the basic summary is we don't think there is an actual
32 bit kernel user of drivers/infiniband for several good reasons.
However we are seeing people want to use a 32 bit user space with 64
bit kernel, which didn't completely work today. So in fixing it we
required a 32 bit rxe user to upgrade their userspace. rxe users are
still already quite rare and we think a 32 bit one is non-existing.
- Fix RDMA uapi headers to actually compile in userspace and be more
complete
- Three shared with netdev pull requests from Mellanox:
* 7 patches, mostly to net with 1 IB related one at the back).
This series addresses an IRQ performance issue (patch 1),
cleanups related to the fix for the IRQ performance problem
(patches 2-6), and then extends the fragmented completion queue
support that already exists in the net side of the driver to the
ib side of the driver (patch 7).
* Mostly IB, with 5 patches to net that are needed to support the
remaining 10 patches to the IB subsystem. This series extends
the current 'representor' framework when the mlx5 driver is in
switchdev mode from being a netdev only construct to being a
netdev/IB dev construct. The IB dev is limited to raw Eth queue
pairs only, but by having an IB dev of this type attached to the
representor for a switchdev port, it enables DPDK to work on the
switchdev device.
* All net related, but needed as infrastructure for the rdma
driver
- Updates for the hns, i40iw, bnxt_re, cxgb3, cxgb4, hns drivers
- SRP performance updates
- IB uverbs write path cleanup patch series from Leon
- Add RDMA_CM support to ib_srpt. This is disabled by default. Users
need to set the port for ib_srpt to listen on in configfs in order
for it to be enabled
(/sys/kernel/config/target/srpt/discovery_auth/rdma_cm_port)
- TSO and Scatter FCS support in mlx4
- Refactor of modify_qp routine to resolve problems seen while
working on new code that is forthcoming
- More refactoring and updates of RDMA CM for containers support from
Parav
- mlx5 'fine grained packet pacing', 'ipsec offload' and 'device
memory' user API features
- Infrastructure updates for the new IOCTL interface, based on
increased usage
- ABI compatibility bug fixes to fully support 32 bit userspace on 64
bit kernel as was originally intended. See the commit messages for
extensive details
- Syzkaller bugs and code cleanups motivated by them"
* tag 'for-linus-unmerged' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (199 commits)
IB/rxe: Fix for oops in rxe_register_device on ppc64le arch
IB/mlx5: Device memory mr registration support
net/mlx5: Mkey creation command adjustments
IB/mlx5: Device memory support in mlx5_ib
net/mlx5: Query device memory capabilities
IB/uverbs: Add device memory registration ioctl support
IB/uverbs: Add alloc/free dm uverbs ioctl support
IB/uverbs: Add device memory capabilities reporting
IB/uverbs: Expose device memory capabilities to user
RDMA/qedr: Fix wmb usage in qedr
IB/rxe: Removed GID add/del dummy routines
RDMA/qedr: Zero stack memory before copying to user space
IB/mlx5: Add ability to hash by IPSEC_SPI when creating a TIR
IB/mlx5: Add information for querying IPsec capabilities
IB/mlx5: Add IPsec support for egress and ingress
{net,IB}/mlx5: Add ipsec helper
IB/mlx5: Add modify_flow_action_esp verb
IB/mlx5: Add implementation for create and destroy action_xfrm
IB/uverbs: Introduce ESP steering match filter
IB/uverbs: Add modify ESP flow_action
...
This change updates the mlx5 interface to create mkey
on the device.
The updates in the command mailbox include increasing the
access mode type field to 5 bits in order to support additional
types such as MLX5_MKC_ACCESS_MODE_MEMIC which represents device
memory access type and will be used when registering MR on allocated
device memory.
All the places that use the old access mode format are adjusted as
well.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This patch adds the mlx5_ib driver implementation for the device
memory allocation API.
It implements the ib_device callbacks for allocation and deallocation
operations as well as a new mmap command support which allows mapping
an allocated device memory to a VMA.
The change also adds reporting of device memory maximum size and
alignment parameters reported in device capabilities.
The allocation/deallocation operations are using new firmware
commands to allocate MEMIC memory on the device.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This patch adds querying of device memory capabilities by the mlx5_core
driver during initialization.
Device memory capabilities is a new capability type and structure
which contains the necessary data that is needed for future device
memory allocation.
The presence of this new capabilities struct is indicated in the
general capabilities struct which is queried first by the driver.
If the presence bit is set, the driver will also query the new
capabilities struct and save it in the device context.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Current Striding RQ HW feature utilizes the RX buffers so that
there is no wasted room between the strides. This maximises
the memory utilization.
This prevents the use of build_skb() (which requires headroom
and tailroom), and demands to memcpy the packets headers into
the skb linear part.
In this patch, whenever a set of conditions holds, we apply
an RQ configuration that allows combining the use of linear SKB
on top of a Striding RQ.
To use build_skb() with Striding RQ, the following must hold:
1. packet does not cross a page boundary.
2. there is enough headroom and tailroom surrounding the packet.
We can satisfy 1 and 2 by configuring:
stride size = MTU + headroom + tailoom.
This is possible only when:
a. (MTU - headroom - tailoom) does not exceed PAGE_SIZE.
b. HW LRO is turned off.
Using linear SKB has many advantages:
- Saves a memcpy of the headers.
- No page-boundary checks in datapath.
- No filler CQEs.
- Significantly smaller CQ.
- SKB data continuously resides in linear part, and not split to
small amount (linear part) and large amount (fragment).
This saves datapath cycles in driver and improves utilization
of SKB fragments in GRO.
- The fragments of a resulting GRO SKB follow the IP forwarding
assumption of equal-size fragments.
Some implementation details:
HW writes the packets to the beginning of a stride,
i.e. does not keep headroom. To overcome this we make sure we can
extend backwards and use the last bytes of stride i-1.
Extra care is needed for stride 0 as it has no preceding stride.
We make sure headroom bytes are available by shifting the buffer
pointer passed to HW by headroom bytes.
This configuration now becomes default, whenever capable.
Of course, this implies turning LRO off.
Performance testing:
ConnectX-5, single core, single RX ring, default MTU.
UDP packet rate, early drop in TC layer:
--------------------------------------------
| pkt size | before | after | ratio |
--------------------------------------------
| 1500byte | 4.65 Mpps | 5.96 Mpps | 1.28x |
| 500byte | 5.23 Mpps | 5.97 Mpps | 1.14x |
| 64byte | 5.94 Mpps | 5.96 Mpps | 1.00x |
--------------------------------------------
TCP streams: ~20% gain
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In some firmware configuration, UMR usage from Virtual Functions is restricted.
This information is published to the driver using new capability bits.
Avoid using UMRs in these cases and use the Firmware slow-path flow to create
mkeys and populate them with Virtual to Physical address translation.
Older drivers that do not have this patch, will end up using memory keys that
aren't populated with Virtual to Physical address translation that is done
part of the UMR work.
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Newer NICs (ConnectX-5 and onward) can apply vlan pop or push as an
action taking place during flow steering. Add the core bits for that.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Added the following packets dropped while vport down statistics:
Rx dropped while vport down - counts packets which were steered by
e-switch to a vport, but dropped since the vport was down. This counter
will be shown on ip link tool as part of the vport rx_dropped counter.
Tx dropped while vport down - counts packets which were transmitted by
a vport, but dropped due to vport logical link down. This counter
will be shown on ip link tool as part of the vport tx_dropped counter.
The counters are read from FW by command QUERY_VNIC_ENV.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Added the following packets drop counter:
Rx steering missed dropped packets - counts packets which were dropped
due to miss on NIC rx steering rules.
This counter will be shown on ethtool as a new counter called
rx_steer_missed_packets.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add support for new FW command QUERY_VNIC_ENV.
The command is used by the driver to query vnic diagnostic statistics
from FW.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Implement set/get functions to configure PFC stall prevention
timeout by tunables api through ethtool.
By default the stall prevention timeout is configured to 8 sec.
Timeout range is: 80-8000 msec.
Enabling stall prevention with the auto timeout will set
the timeout to 100 msec.
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add the needed capability bit and counters to device spec description.
Expose the following two counters in ethtool:
tx_pause_storm_warning_events: when the device is stalled for a period
longer than a pre-configured watermark, the counter increase, allowing
the debug utility an insight into current device status.
tx_pause_storm_error_events: when the device is stalled for a period
longer than a pre-configured timeout, the pause transmission is disabled,
and the counter increase.
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add two new parameters: max_burst_sz and typical_pkt_size (both
in bytes) to rate limit configurations.
max_burst_sz: The device will schedule bursts of packets for an
SQ connected to this rate, smaller than or equal to this value.
Value 0x0 indicates packet bursts will be limited to the device
defaults. This field should be used if bursts of packets must be
strictly kept under a certain value.
typical_pkt_size: When the rate limit is intended for a stream of
similar packets, stating the typical packet size can improve the
accuracy of the rate limiter. The expected packet size will be
the same for all SQs associated with the same rate limit index.
Ethernet driver is updated according to this change, but these two
parameters will be kept as 0 due to lacking of proper way to get the
configurations from user space which requires to change
ndo_set_tx_maxrate interface.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Add helper functions that check if a protocol is
part of a flow steering match criteria.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently, we don't support egress flow steering namespace in mlx5
flow steering core implementation. However, when we want to encrypt
a packet, we model it as a flow steering rule in the egress path.
To overcome this, we add an empty egress namespace to flow steering.
This namespace is initialized only when ipsec support exists.
In the future, this will grow to a full blown full steering
implementation, resembling the ingress path.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Pull networking updates from David Miller:
1) Significantly shrink the core networking routing structures. Result
of http://vger.kernel.org/~davem/seoul2017_netdev_keynote.pdf
2) Add netdevsim driver for testing various offloads, from Jakub
Kicinski.
3) Support cross-chip FDB operations in DSA, from Vivien Didelot.
4) Add a 2nd listener hash table for TCP, similar to what was done for
UDP. From Martin KaFai Lau.
5) Add eBPF based queue selection to tun, from Jason Wang.
6) Lockless qdisc support, from John Fastabend.
7) SCTP stream interleave support, from Xin Long.
8) Smoother TCP receive autotuning, from Eric Dumazet.
9) Lots of erspan tunneling enhancements, from William Tu.
10) Add true function call support to BPF, from Alexei Starovoitov.
11) Add explicit support for GRO HW offloading, from Michael Chan.
12) Support extack generation in more netlink subsystems. From Alexander
Aring, Quentin Monnet, and Jakub Kicinski.
13) Add 1000BaseX, flow control, and EEE support to mvneta driver. From
Russell King.
14) Add flow table abstraction to netfilter, from Pablo Neira Ayuso.
15) Many improvements and simplifications to the NFP driver bpf JIT,
from Jakub Kicinski.
16) Support for ipv6 non-equal cost multipath routing, from Ido
Schimmel.
17) Add resource abstration to devlink, from Arkadi Sharshevsky.
18) Packet scheduler classifier shared filter block support, from Jiri
Pirko.
19) Avoid locking in act_csum, from Davide Caratti.
20) devinet_ioctl() simplifications from Al viro.
21) More TCP bpf improvements from Lawrence Brakmo.
22) Add support for onlink ipv6 route flag, similar to ipv4, from David
Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1925 commits)
tls: Add support for encryption using async offload accelerator
ip6mr: fix stale iterator
net/sched: kconfig: Remove blank help texts
openvswitch: meter: Use 64-bit arithmetic instead of 32-bit
tcp_nv: fix potential integer overflow in tcpnv_acked
r8169: fix RTL8168EP take too long to complete driver initialization.
qmi_wwan: Add support for Quectel EP06
rtnetlink: enable IFLA_IF_NETNSID for RTM_NEWLINK
ipmr: Fix ptrdiff_t print formatting
ibmvnic: Wait for device response when changing MAC
qlcnic: fix deadlock bug
tcp: release sk_frag.page in tcp_disconnect
ipv4: Get the address of interface correctly.
net_sched: gen_estimator: fix lockdep splat
net: macb: Handle HRESP error
net/mlx5e: IPoIB, Fix copy-paste bug in flow steering refactoring
ipv6: addrconf: break critical section in addrconf_verify_rtnl()
ipv6: change route cache aging logic
i40e/i40evf: Update DESC_NEEDED value to reflect larger value
bnxt_en: cleanup DIM work on device shutdown
...
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJabj6pAAoJEHm+PkMAQRiGs8cIAJQFkCWnbz86e3vG4DuWhyA8
CMGHCQdUOxxFGa/ixhIiuetbC0x+JVHAjV2FwVYbAQfaZB3pfw2iR1ncQxpAP1AI
oLU9vBEqTmwKMPc9CM5rRfnLFWpGcGwUNzgPdxD5yYqGDtcM8K840mF6NdkYe5AN
xU8rv1wlcFPF4A5pvHCH0pvVmK4VxlVFk/2H67TFdxBs4PyJOnSBnf+bcGWgsKO6
hC8XIVtcKCH2GfFxt5d0Vgc5QXJEpX1zn2mtCa1MwYRjN2plgYfD84ha0xE7J0B0
oqV/wnjKXDsmrgVpncr3txd4+zKJFNkdNRE4eLAIupHo2XHTG4HvDJ5dBY2NhGU=
=sOml
-----END PGP SIGNATURE-----
Merge tag v4.15 of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git
To resolve conflicts in:
drivers/infiniband/hw/mlx5/main.c
drivers/infiniband/hw/mlx5/qp.c
From patches merged into the -rc cycle. The conflict resolution matches
what linux-next has been carrying.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Allow to specify the size of the hairpin queues along with the
packet buffer data size from the core setup code.
If the driver doesn't provide this, the FW applies proper value that
matches the provided data size and a FW chosen RQ stride size.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The latest merge between net and net-next introduced a complier assert in
mlx5 driver. In hca_cap_bits older fields are kept along with newer
fields that should have replaced them.
Fixes: c02b3741eb ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are systems platform information management interfaces (such as
HOST2BMC) for which we cannot disable local loopback multicast traffic.
Separate disable_local_lb_mc and disable_local_lb_uc capability bits so
driver will not disable multicast loopback traffic if not supported.
(It is expected that Firmware will not set disable_local_lb_mc if
HOST2BMC is running for example.)
Function mlx5_nic_vport_update_local_lb will do best effort to
disable/enable UC/MC loopback traffic and return success only in case it
succeeded to changed all allowed by Firmware.
Adapt mlx5_ib and mlx5e to support the new cap bits.
Fixes: 2c43c5a036 ("net/mlx5e: Enable local loopback in loopback selftest")
Fixes: c85023e153 ("IB/mlx5: Add raw ethernet local loopback support")
Fixes: bded747bb4 ("net/mlx5: Add raw ethernet local loopback firmware command")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add hairpin definitions to the IFC file.
This includes the HCA ID, few HCA hairpin capabilities, new
fields in RQ/SQ used later for the pairing and the WQ hairpin
data size attribute.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When mlx5_ib_add is called determine if the mlx5 core device being
added is capable of dual port RoCE operation. If it is, determine
whether it is a master device or a slave device using the
num_vhca_ports and affiliate_nic_vport_criteria capabilities.
If the device is a slave, attempt to find a master device to affiliate it
with. Devices that can be affiliated will share a system image guid. If
none are found place it on a list of unaffiliated ports. If a master is
found bind the port to it by configuring the port affiliation in the NIC
vport context.
Similarly when mlx5_ib_remove is called determine the port type. If it's
a slave port, unaffiliate it from the master device, otherwise just
remove it from the unaffiliated port list.
The IB device is registered as a multiport device, even if a 2nd port is
not available for affiliation. When the 2nd port is affiliated later the
GID cache must be refreshed in order to get the default GIDs for the 2nd
port in the cache. Export roce_rescan_device to provide a mechanism to
refresh the cache after a new port is bound.
In a multiport configuration all IB object (QP, MR, PD, etc) related
commands should flow through the master mlx5_core_dev, other commands
must be sent to the slave port mlx5_core_mdev, an interface is provide
to get the correct mdev for non IB object commands.
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Generate a unique 128bit identifier for each host and pass that value to
firmware in the INIT_HCA command if it reports the sw_owner_id
capability. Each device bound to the mlx5_core driver will have the same
software owner ID.
In subsequent patches mlx5_core devices will be bound via a new VPort
command so that they can operate together under a single InfiniBand
device. Only devices that have the same software owner ID can be bound,
to prevent traffic intended for one host arriving at another.
The INIT_HCA command length was expanded by 128 bits. The command
length is provided as an input FW commands. Older FW does not have a
problem receiving this command in the new longer form.
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
In mlx5_ifc, struct size was not complete, and thus driver was sending
garbage after the last defined field. Fixed it by adding reserved field
to complete the struct size.
In addition, rename all set_rate_limit to set_pp_rate_limit to be
compliant with the Firmware <-> Driver definition.
Fixes: 7486216b3a ("{net,IB}/mlx5: mlx5_ifc updates")
Fixes: 1466cc5b23 ("net/mlx5: Rate limit tables support")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Gal Pressman